Jump to content
SAU Community

Recommended Posts

  • Replies 126
  • Created
  • Last Reply

Top Posters In This Topic

Mark: Thanks for the tip. The motorbike course yesterday was so boring. Was all silly stuff you should already know - how to mount a motorbike, how to engage clutch, how to start motorbike etc. When the time comes to do the P's test, you can give me some pointers. Is the L's computer test at the RTA difficult, or just common knowledge?

Chris

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1128412
Share on other sites

Mark:  Thanks for the tip.  The motorbike course yesterday was so boring.  Was all silly stuff you should already know - how to mount a motorbike, how to engage clutch, how to start motorbike etc.  When the time comes to do the P's test, you can give me some pointers.  Is the L's computer test at the RTA difficult, or just common knowledge?

Chris

Yep I hear you. Super boring. You don't go over about 30kmh and 2km from my house is an 80 zone I take to work - so very daunting when I had zero bike experience...took a few days to warm up (read: build confidence!) to doing 80.

I'd be very happy to pass pointers for the P's. The best advice I can give right now, is to plan on hiring a CB for the test. If you ride a ZZR or a CBR or anything like that, the U-turn and cones are nearly impossible. My ZZR was plenty fast, but designed for handling at speeds above walking pace. I practiced for probably ten hours over a few weeks (in a cul de sac) and still only just scraped through on the ZZR. I tried the test on a CB250 and nailed it 100% (no touches/ feet down/ etc.)

Re: the comp test - take the time to study up on the bike stuff. There is all the normal L-permit q's, plus lots of bike specific. An hour of reading will prob save you time/effort/$$. Most if it is the stuff you forget 5 mins after leaving the RTA, like how close in metres can you park to a bus zone? and similar stuff.

Well now that I've typed all this I realise it I should have sent it via PM. Apologies to all the guys reading this who don't ride! :P

Mark

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1129411
Share on other sites

Whilst I'm in the Newcastle thread, to any other guys in the Bay/Medowie/Terrace/Maitland area (ie. northside) always seem to get stuck behind people driving at 80kmh in the 100 zones? Richardson road past Grahamstown dam, and the road out to Maitland are terrible for it.

I don't understand it. Are the drivers unaware? I find that hard to believe as it happens too often to be tourists/non-locals. Which makes me think that it must be people who choose to do 80kmh in some attempt to reduce road accidents... whilst everyone else gets fed up and overtakes (higher risk, yeah?).

I'm sorry guys, I just feel like ranting, cause I get so sick of it. You overtake and the driver is happily tooling along below the speed limit. The areas are 100 for a reason - there's nothing else there! No merging, no driveways, nothing! And I seem to get the "Flashy Flashy" high-beams from them as I pass, as if I'm some P-plater driving a turbo V8 with a car full of passengers in the middle of the night!?

Man, people need to get a grip. Self-included. I know i'll get where I'm going eventually, but to me it highlights the driver ed thing. If people are uncomfortable being in control of their 2-ton 4WD at 100kmh, either go take some professional training or ask someone else to drive.

*sigh*

Mark

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1129422
Share on other sites

SHOULD COME!  

Fresh ?? paul and stace?? mic33r?? ER34GTT?? BNR32?? guilt top?? lenno ?? bojo1???

Sorry guys, I've just been really busy lately. I'll try and make it to a cruise next year (assuming my car isn't sold by then), but it's just hectic at this time of the year.

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1129682
Share on other sites

Whilst I'm in the Newcastle thread, to any other guys in the Bay/Medowie/Terrace/Maitland area (ie. northside) always seem to get stuck behind people driving at 80kmh in the 100 zones? Richardson road past Grahamstown dam, and the road out to Maitland are terrible for it.

I don't understand it. Are the drivers unaware? I find that hard to believe as it happens too often to be tourists/non-locals. Which makes me think that it must be people who choose to do 80kmh in some attempt to reduce road accidents... whilst everyone else gets fed up and overtakes (higher risk, yeah?).  

I'm sorry guys, I just feel like ranting, cause I get so sick of it. You overtake and the driver is happily tooling along below the speed limit. The areas are 100 for a reason - there's nothing else there! No merging, no driveways, nothing! And I seem to get the "Flashy Flashy" high-beams from them as I pass, as if I'm some P-plater driving a turbo V8 with a car full of passengers in the middle of the night!?

Man, people need to get a grip. Self-included. I know i'll get where I'm going eventually, but to me it highlights the driver ed thing. If people are uncomfortable being in control of their 2-ton 4WD at 100kmh, either go take some professional training or ask someone else to drive.

*sigh*

Mark

I know exactly what you mean. The palce I used to get stuck all the time was on the way to Williamtown from Newcastle on NB road. I used to work out there, so I'd have to put up with it daily. It was crazy.

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1129685
Share on other sites

Yep it's up for sale on Carsales right now. I've had it since 2001, so it's time for a change. I'm staying in the import scene though, but going across to Toyota. Hopefully I'll be in a JZX100 Chaser by the start of next year.

The Skyline was good, but I just don't drive it much anymore. I'll still be a regular on the forums though, as I can't find any decent Toyota forums (and I like this place).

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1129726
Share on other sites

Mark: P's shouldn't be too hard on my bike I've already got, a TTR 250 and the instructors told me its very easy to do the U-Turn on a trailbike. I bought this a month ago, then realised you can get up to 650cc on your L's on the weekend. I would have a gone a XR400 or similar, but the 250 will be plenty quick enough for now. Organising a sand paddle and 2nd rear rim so I can take it out on the beach!!!

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1130299
Share on other sites

Hay Guys,

just seeing if any one is up for a cuize in early Jan, i ahave had my car for about 4 months now and i a m keen to got for a cruize with some other lines. Even for a small cruize to the bay or similar.

Ta

P.S have a good and safe Chrissy.

Link to comment
https://www.sau.com.au/forums/topic/44473-newcasle/page/5/#findComment-1135560
Share on other sites

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Ps i found the below forum and it seems to be the same scenario Im dealing with. Going to check my ECU coolant temp wire tomorrow    From NICOclub forum: s1 RB25det flooding at start up Thu Apr 11, 2013 7:23 am I am completely lost on this. Car ran perfectly fine when I parked it at the end of the year. I took the engine out and painted the engine bay, and put a fuel cell with an inline walbro 255 instead of the in tank unit I had last year. After reinstalling everything, the engine floods when the fuel pump primes. if i pull the fuel pump fuse it'll start, and as soon as I put the fuse back in it starts running ridiculously rich. I checked the tps voltage, and its fine. Cleaned the maf as it had some dust from sitting on a shelf all winter, fuel pressure is correct while running, but wont fire until there is less than 5psi in the lines. The fuel lines are run correctly. I have found a few threads with the same problem but no actual explanation of what fixed it, the threads just ended. Any help would be appreciated. Rb25det s1 walbro255 fuel pump nismo fpr holset hx35 turbo fmic 3" exhaust freddy intake manifold q45tb q45 maf   Re: s1 RB25det flooding at start up Fri Apr 12, 2013 5:07 am No, I didn't. I found the problem though. There was a break in one of the ecu coolant temp sensor wires. Once it was repaired it fired right up with no problems. I would have never thought a non working coolant temp sensor would have caused such an issue.
    • Hi sorry late reply I didnt get a chance to take any pics (my mechanics on the other side of the city) but the plugs were fouled from being too rich. I noticed the MAF wasn't genuine, so I replaced it with a genuine green label unit. I also swapped in a different ignitor, but the issue remains. I've narrowed it down a bit now: - If I unplug and reconnect the fuel lines and install fresh spark plugs, the car starts right up and runs perfectly. Took it around the block with no issues - As soon as I shut it off and try to restart, it won't start again - Fuel pressure while cranking is steady around 40 psi, injectors have good spray, return line is clear, and the FPR vacuum is working. It just seems like it's getting flooded after the first start I unplugged coolant sensors to see if its related to ECU flooding but that didnt make a difference. Im thinking its related to this because this issue only started happening after fixing coolant leaks and replacing the bottom part of the stock manifolds coolant pipe. My mechanic took off the inlet to get to get to do these repairs. My mechanics actually just an old mate who's retired now so ill be taking it to a different mechanic who i know has exp with RBs to see if they find anything. If you have any ideas please send em lll give it a try. Ive tried other things like swapping the injectors, fuel rail, different fuel pressure regs, different ignitor, spark plugs, comp test and MAF but the same issue persists.
    • My return flow is custom and puts the return behind the reo, instead of at the bottom. All my core is in the air flow, rather than losing some of it up behind the reo. I realise that the core really acts more as a spiky heatsink than as a constant rate heat exchanger, and that therefore size is important.... but mine fits everything I needed and wanted without having to cut anything, and that's worth something too. And there won't be a hot patch of core up behind the reo after every hit, releasing heat back into the intake air.
    • There is a really fun solution to this problem, buy a Haltech (or ECU of your choice) and put the MAF in the bin.  I'm assuming your going to want more power in future, so you'll need to get the ECU at some stage. I'd put the new MAF money towards the new ECU. 
    • Any idea where I can get genuine MAF apart from used ones? I can't find any only for GTRs and unfortunately that price is not in my budget 🤣 I might gap my plugs down and put my splitfires in, they were only in for a year or so before I started the rebuild 
×
×
  • Create New...