Jump to content
SAU Community

Recommended Posts

I have a very bad habit of warping or hotspotting discs in all my previous cars, and want to nip this in the budd before I start doing any damage.

http://www.mossmotors.com/sitegraphics/pages/brake_discs.html

change to better than factory pads and brake fluid for your driving application, replace factory discs with better ones also help.

FYP

Lol

What was so funny? My saying the Evo had fulleh hektic stretch?

There was quite a few gold quotes in there really. I've forgotten them all now though :P. But yeah mainly this:

I thought the general "I turn happy laps into angry laps" vibe was the funny bit... :D

Buy me an external mic then.

No.

There was quite a few gold quotes in there really. I've forgotten them all now though :P. But yeah mainly this:

No.

Like, 'is that an old evo or just a dirty f**king lancer'?

Then you have to put up with my engine noise.

Like, 'is that an old evo or just a dirty f**king lancer'?

Then you have to put up with my engine noise.

I like the one where you say 'I was going to....but then I realised it's Mr Ants and he might get butthurt' farkin lol

Speaking of brakes - I know this is probably the wrong place to ask, but the right place for the people I'd respect the answer from most - what should I put on a V36 350GT? I have a very bad habit of warping or hotspotting discs in all my previous cars, and want to nip this in the budd before I start doing any damage.

Depends on which calipers you're running. If it's the basic ones, scrap them and replace with either Akebono or R34 bits. Akebonos are about $2k though.

Also take a look at what rotors and pads you're running. The right mix will help but if the size isn't right, you'll still get heaps of brake fade. I am the master of brake fade! :P

RDA slotted and dimpled combined with QFM or EBC pads should give you a good go.

Depends on which calipers you're running. If it's the basic ones, scrap them and replace with either Akebono or R34 bits. Akebonos are about $2k though.

Also take a look at what rotors and pads you're running. The right mix will help but if the size isn't right, you'll still get heaps of brake fade. I am the master of brake fade! :P

RDA slotted and dimpled combined with QFM or EBC pads should give you a good go.

Thanks mate :cheers:

I am planning on RDA slotted and dimpled with EBC Red Stuffs in mine...

I gotta admit... jibberish... all jibberish! :P

I have much to learn. Maybe one day I'll be able to afford to have a dedicated track day car to put my money into - and maybe then I'll understand what "RDA slotted and dimpled" means without automatically picturing some exotic condom style.

my mate took the photos and gave me links to them, so I just posted them up as is... I don't know much about photos/compression but it sounds like you need faster internet? :P

should you post more dirty Evos in the future just save them on your desktop resize the pix like 1/3 and then post them up (I use photobucket or my mobile to post all my sexy photos)

Flickr should offer compression by changing the "_o.jpg" to "_z.jpg", or other letters. None of them work.

I blame your friend for not allowing Flickr to auto-compress linked photos.

Either that or he's shared his view address, not the public address.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Reading through the engine service manual their advice is do a cylinder balance test. Unplug one injector at a time and see if the idle drops a consistent RPM. You can also do this using a Consult cable which is easier. They also call for unplugging the power transistor, then with the engine off and the fuel rail unhooked from the manifold verifying that you have good fuel flow (even injection, no dripping/leaks, etc) when you twist the CAS by hand. Also verify the spark by pulling the spark plugs and allowing the plugs to ground and turning the CAS by hand. I would also start doing the sensor checks and idle valve checks in service manual. Make sure the MAF tests reasonably, the intake air regulator is sane, etc. You may have to get new spark plugs.
    • This sounds very old of me, however since buying the Tiguan shit box, my view on shit boxes have changed.
    • I've looked up the parts number (41011AL501). It's around $700 OEM. Usually our Infiniti G35 here in Canada have interchangeable parts with my Stagea but the parts number are not the same. I have looked around and it seems the JDM 2005 V35 Skyline (which is the same as our G35) has the same caliper but I cannot confirm. And I can't find a repair kit. The inner brake pads drags on the rotor, seems to be rusty piston. Thanks for the info by the way
    • This coupled with 6-9 speed autos with ridiculously short gearing is why these modern shitbox cars always seem so fast off the line. If it wasn't for those things, Raptors would not seem fast. The problem we have is there is a driveability gap between a more gentle take off and a wheelspinning sideways launch. The difference between ankle flex required to achieve one and ankle flex required to achieve the other is about 0.5°.
    • Yeah I think I'm also with the opposite here. It's 'hard to keep up with traffic' because in the real world I'm accelerating with 15% throttle and they are pinning it. It feels like I'm being an overt dickhead at anything above 15% throttle, so the car sounds like I'm being an overt dickhead to keep up with/get ahead of traffic when I'm really just trying to drive with traffic. There would be no issue 'keeping up with traffic' if we used the same level of throttle input/aggression to drive around. People really do just drive around with their foot nearly pinned in econoboxes.
×
×
  • Create New...