Jump to content
SAU Community

#7 Sydney Skyline Cruise - Wiseman's Ferry

smiik33

By smiik33,
in Events Archive

 Share

Recommended Posts

smiik33 Enthusiast

smiik33

Posted
Posted

Hello again my fellow skyline enthusiasts. I do apologize for the delay but my #7 cruise is as follows:

Meeting point:

13th of July, 9:45am at Thornleigh Maccas being ready to depart at 10:30am sharp

Series of events:

We will be traveling up the M1 exiting on Peats Ridge Road. For those that would have forgotten to fill up, there is a Caltex just before our 1st stop at the springs where we will take 15 min for a photo shoot.

Continuing up Peats Ridge Road, we'll almost immediately make a left onto George Downes Drive which we'll follow through until we turn left onto Wiseman's Ferry Road. Fairly straight forward once we're here until we get to my surprise turn off. We will be making an extra special stop for another photo shoot that I have organized which I am sure everyone will be very appreciative of the efforts I've gone through. DO NOT BE ALARMED, THERE ARE NO OFF ROAD SECTIONS AS I HAVE LEARNED FROM MY PREVIOUS CRUISE. ALL DRIVING WILL BE CARRIED OUT ON SEALED NSW ROADS.

Once we're all done with the photo shoot, we'll continue along Wiseman's Ferry Road right down to the ferry itself, cross over and make another stop a few hundred metres ahead on the left on the grass field (parking lot and limited street parking nearby for those not wanting to park on grass). Anyone wanting to eat is more than welcome to join us at Wiseman's Ferry Inn for lunch.

On this side of the ferry the road becomes Old Northern Road. After lunch we'll travel along Old Northern Road right through to Dural where it joins onto New Line Road, following New Line Road to the end where we'll turn left onto Pennant Hills Road.

Ending point:

We'll coast along Pennant Hills Road where we'll finish up at the parking lot of Carlingford Court located at the corner of Pennant Hills Road and Carlingford Road.

PLEASE NOTE:

Today I have just finished a scout cruise of exactly what has been detailed above to get a better understanding of the drive. There are no issues with the route planned whatsoever except for a few uneven surfaces which we'll compromise with driving 10 - 20km under the limit. A more detailed description of the drive will be given on the day at the meeting point.

Remember to spread the word out as this will be a fantastic day!

PM me on here or text me on 0433396407 for more information.

Thanks

Danny

post-127471-14040203850252_thumb.jpg

post-127471-14040203956494_thumb.jpg

post-127471-14040204056251_thumb.jpg

 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • PranK
      eBay "Hella" oil level sensor

      By PranK · Posted

      Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • Kinkstaah
      Jacks that fit under GTR lips that can reach the subframe?

      By Kinkstaah · Posted

      I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • TurboTapin
      R32 GTST - 600KW+ RB28/CD009 Build

      By TurboTapin · Posted

      Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • TurboTapin
      Jacks that fit under GTR lips that can reach the subframe?

      By TurboTapin · Posted

      So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • suko
      J50 clock date suddenly reset to January 1

      By suko · Posted

      Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...