Jump to content
SAU Community

Recommended Posts

1. SW20 Rail came off a bride brix 1.5 it's driver side
Price $150

14509581142_e1416c10c7_c.jpg

14324090109_bfec6674a4_c.jpg

2. R33 Bride Drivers Side, Side Mount Rail to suit fixed back seats
Price: $150

20140427_153904_zps8214baa6.jpg

20140427_153917_zps305588b4.jpg


3. SSR Gartmier Rims 18x8.5+32 18x9.5+32 235/40 245/40 near new tyres all round
Price: $1000

14324331877_699560a24b_c.jpg

Rims are abit rough looks like they haven't been cleaned in a while with a lot of brake dust stock on the lip and face
14509402184_23e95db307_c.jpg

14487662926_6a233a7ac7_c.jpg

14530870373_dfa4264f37_c.jpg

14530870373_dfa4264f37_c.jpg

14509382774_2b1609794e_c.jpg

14324141009_c4f3242683_c.jpg

14324086960_1004a04564_c.jpg

4. Work Euroline N2s Pair Only 18x10-11 Tyres are Shagged
Price: $750

14509615002_18fc8f37bf_c.jpg

14509599442_a132cd587f_c.jpg

14324268387_01ffd8893e_c.jpg

14324264137_858c7fb194_c.jpg

14510709575_197bc3892b_c.jpg

5. Work Euroline 18x9-23 R disk so maximum brake clearance no tyres
$750

14586391002_4d563596ec_c.jpg

14400454520_29fb27c367_c.jpg

14607200723_4796e66c00_b.jpg

6. R33 Rear Guards Kmak Aero 40mm
$200

20140427_154137_zps25e4b4f2.jpg

7. AAR Fixed Back Seat
$400

20140427_153823_zpsb47df001.jpg

20140427_153831_zpsc2065c79.jpg



Located Hurstville Area
Contact via PM or SMS
0421079631
Benny

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Wife wanted basket things in the wardrobe in our temporary house. Thought about ripping our the wardrobe and fitting the entire IKEA set, but it's a temporary house and we want to move in a few years. So IKEA advertises this as a 50cm unit, however the actually basket and rails measure 46cm wide. Only issue was depth, IKEA stuff is quite deep, where as the builder special junk is super shallow at less than 40cm. Send it, chopped the rails, then offset the mounting holes, job done, happy wife, less shit scattered all over the bedroom. Did the same to the other side too. Also drove the Skyline shit box today, dropped off oil at Supercheap Auto. I didn't realise they only now take max 2x bottles per visit. I visited 2x Supercheap Autos.  
    • I've seen similar actually in my situation. You never know what tables are attempted to be used when the car thinks it's -99C or +200C. The fail state is not usually that extreme but you know what I mean - it was in my case though! This is where being able to read all the sensors is useful cause you see this stuff really quickly.
    • The above is very important. However as long as you keep timing relatively low, it's plausible to make your own knock ears and plausible to learn to tune with a modern ECU that can do wideband O2 correction like a boost controller. I mean if you only have one viable road to even drive the car on, learning to tinker to this level may be worth doing given you can't do much else with the car...?
    • I find the fact that the rear plate has to be bent inwards at the rear not so bad: but the front is just awful: It's like come on. (these are my very old, now retired/turned in plates) TBH it is a lot of money to fix a minor issue, the fact I said "I'll never really spend the money on doing this" is why people ended up buying them as a gift for a 'car guy' who can be hard to shop for.. for car guy things.
    • I just bent the ends of my premo plates. It even went through Regency like that after the engine conversion and the inspector (a great bloke!) just squinted his eyes and said "I didn't see that". Plates, and how they look, are just something that have zero importance to me.
×
×
  • Create New...