Jump to content
SAU Community

Recommended Posts

Parting out my S13 project car as I will no longer have time to complete it or drive it so everything must go.

S13 origin type2 50mm rear over fenders as new condition three tiny pilot holes drilled on each fender for test fitting $300

S13/180sx Apexi Power FC ECU + Hand controller Serial no. PFC SR2015 020-0601 $650

SR20 Kelway steam pipe manifold external gate suits T3 flanged turbos brand new only test fitted $500

S13/180sx Blacktop SR20DET has 98,XXX kms on engine minus turbo,manifold,ECU (PFC can be negotiated with price) included KTS extended baffled trap door sump, engine loom, starter motor $1500

Trust/Greddy rocker arm stoppers brand new $100

S13/180sx 5sp manual gearbox with shifter will needs new shifter boot $450
SR20DET flywheel $50
S13/180sx Manual master cylinder $30
S13/180sx clutch pedal $30
S13/180sx Brake pedal $30
S13/180sx manual tail shaft $80

OR

Complete manual conversion for S13/180 $550

S13/180sx/R32 rear traction arms pair $40 or $20 each x2
S13/180sx/R32 rear camber arm pair $40 or $20 each x2
S13/180sx/R32 rear lower control arm $60 or $30 each x2

Location northern suburbs
Additional pics can be sent upon request
Contact Anthony
0466111592

post-38352-0-60469600-1406274554_thumb.jpgpost-38352-0-36530000-1406274583_thumb.jpgpost-38352-0-69084200-1406274683_thumb.jpgpost-38352-0-15076900-1406274697_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Did and sync timing with light 
    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
×
×
  • Create New...