Jump to content
SAU Community

Recommended Posts

Got this weird boost cut thing thats been happening since last night, ran out of ideas, not sure what to do :(

At WOT, i get the full 1.3-1.5 bars of boost, but once i hit 5-6k revs, the boost drops off completely, and the revs climbs slowly (basically like a n/a), If i shift before i hit 5000 revs, the boost is still good (roughly 1-.1.5 bars), however once i push it to 5000revs, all the boost just drops again, and the car barley accelerates. Once i shift, the car gets back onto boost till i hit 5000revs again. No clue why its happening ==;

It happened around 15 minutes after i filled up, so thought maybe it might be a bad batch of fuel??? But then i thought, if thats the case it would be pinging as soon as i hit boost...

Boost range:

- 1st gear: 1 bar, then drops off at 5000revs to 0 (or below)

- 2nd gear: 1.2 bars, then drops off at 5000 revs to 0 or below

- 3rd gear WOT (from a 40kph pull) 1.5 bars till i hit 5000 revs then drops off again.....

If its hitting high pressure of boost, i have no clue what the problem is :/ anyone got any ideas?

Things ive done:

- Check MAF sensor cabling

- Cleaned MAF sensor with maf sensor cleaner

- Checked for boost leaks, tightened all clamps

- Chucked in some octane booster
- Unplugged battery to reset the ECU

Things to note:
- Spark plugs are 5000ks new
- Evo is tuned for 98 octante fuel
- Car runs 100% from 0-4900 revs
- No knocking (cant hear anything)
- Idle is still smooth
- Car starts with ease

Any help will be much appreciated :)

Link to comment
https://www.sau.com.au/forums/topic/446615-boost-cuts-out-at-5000rpm/
Share on other sites

#@luke gtr
Yea i was thinking the MAF sensor was playing up, took it out and cleaned it thoroughly, yet to test it out... Also noticed the bolts came off the air box on the maf sensor, so there was a little gap between the airbox and maf.

Could it be a fuel pump on its way out by any chance?

#@scotty nm35
Ill have a look at that today, will do a smoke test to check for leaks...
The BOV is pretty new, i doubt its opening early, its a mr edition bov.

Update:

Just took it for a drive, ran a bit better, but boost is still dropping off at 6000 revs ==;

After the boost dropped on 1st @5900ish rpm, i switched to 2nd @ WOT, then as soon as the boost began to drop, i quickly switched to third before the boost completely dropped off, at which point the boost quickly shot up to 1.5bars @4000rpm, It feels like the car really doesnt want to rev past 5000-6000. Feels like the its cutting out boost for a reason. I also have a check engine light now :/ Will need to check the error code tomorrow.

  • 2 weeks later...

Ended up fixing the boost cut finally :D Turns out there was no cut, it was just the intake pipe collapsing in on boost at high revs, hence why i had no boost. We stretched out the airbox a little to create tension, which resulted in no more collapsing :)

Very hard thing to look for when having boost cuts, cause the intake pipe always rises when you pull over and check, so you'd think its all fine ...

Cheers for all the help :)

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 3 Kids are starting to hit that ages. I wanted to get them something special to learn on, put down the screens and have some fun. 4Door 2001 R34DE Black Pearl GV1 Jap Import, AU 2nd owner. Pre Work done. Suspension - Wheels Pedders SportsRyder Coilovers   Wheels TSG Spokey Boi 18'x9.5"+15 Body JASI Aero 4 door Type R Full Kit LED Conversion - Parker, Blinkers, & Reverse Exhaust Hurricane Headers 100 CPI high flow cat 2.5" Piping Cannon muffler Internal Bride low max stradia ii - front seats  Bride RO seat base and Rails (R/H) Cube short shifter LED Conversion - Interior   
    • Why are you so adamant on going M12? Why not follow Brad (GTSBoy) suggestion. You're talking moving from a 1/8" size, to a 1/2" effectively. 4 times bigger. Why skip the commonly available sizes in between? The bigger you go, the more likely you are to strip the threads out at a later date, as guaranteed, someone will put a huge spanner on the M12 and really tighten it up, and you're only in thin wall, so not a lot of threads to engage!
    • Hi. Yeah thanks. Car is already at tuners and it staying there to resolve "many" issues they do not like. So it is in a good hands. Getting a good tune on that Nistune ECU too so the car would be good. Just needs a little tune up and love.
    • Probably gonna remove manifold and turbo. I’m not sure if I can get M12 x 1.5 air tight. Could use high temp Loctite 246 or something similar, but I don’t know. Maybe it’s just best to remove everything again and weld an 1/8NPT on there instead.
    • Yeah, saw the ratios, not impressed. Would like the punch I have in the first gears now. With those ratios it won't be the same.  Also want the h pattern gearing, or at least a quiet gear set that don't need to come apart for service each year. Looks like the only "reasonable" way Is a 8hp70 transmission, but where is the fun in that🤷‍♂️
×
×
  • Create New...