Jump to content
SAU Community

Selling R32 Gtr Nsw Black $12,500 Cheap Quick Sale !

Longz

By Longz,
in For Sale (Private Whole cars only)

 Share

Recommended Posts

Longz Mentor

Longz

Posted
Posted

Selling a Project R32 GTR i picked up a while ago it's currently sitting at my Mechanic at smithfield , The motor has completley been rebuilt by a Mechanic in Canberra.

Inspection of the head etc will show you it's all very new and clean.

Asking Price $12,500 ono i've set the price low as i would like a quick easy sale. No Lowballers.

Car currently has no rego.

KM'S 118,000

Engine Specs:
Wiseco forged pistons
Eagle h-beam forged conrods with ARP bolts
Nitro 1.5mm mlsr head gasket
ACL race rod bearings
ACL race main bearings
Tomie 260 deg cams (inlet and exhaust)
Ported head, with full service and new seals
Tomei head stud kit
All new genuine nissan gaskets and seals
New N1 oil pump

Engine bay:
Brand new alloy radiator
Turbo smart duel stage boost controller
JJR duel pod filter induction kit
Newly fitted abs unit
Full silicone water and vacume hose kit (black)
Painted engine covers and intake manifold (tiger mica gold looking)
New gates engine belts including gates race silicone belt and new tensioners
New Nissan water pump
New Nissan coil pack loom
Mines ecu
3 inch twin front pipes
3.5 inch exhaust

Drive line:
Nismo twin plate
Good box and diffs
New transmission oil
New diff oils
New 4wd oil (Nissan matic d)
All shaft good
Vented and cross drilled discs
Good tyres (about 50%)

Body:
This is really the only thing that lets this cars down
Paint is average
The car was owned by a senior in Japan and it shows (has the Japanese p sticker)
Two owner car 1 in Japan and 1 in Australia
It has a few door bangs
Rust in the lower rear quarter panels
Crack in the front bar
Dented front left quarter (in the wheel arch)
Small dent in the bonnet

Interior:
Mostly factory
Genuine recaro in good shape (1 burn)
Genuine recaro seat rail
Factory passenger seat
Normal skyline interior with split stitching on shifter and hand brake no cracks on the dash
One broke vent (far left vent)
Carpet is good

post-70289-0-13347900-1407674804_thumb.jpg

post-70289-0-20166800-1407674809_thumb.jpg

post-70289-0-89565300-1407674818_thumb.jpg

post-70289-0-22580300-1407674824_thumb.jpg

kawasakirider Grand Master

kawasakirider

Posted
Posted

As above, strong interest.

I'm from Brisbane but I may try to arrange someone to inspect on my behalf on Saturday.

Is the rust repairable? It really is the end of a car if it's not nipped in the bud instantly....

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      R32 Gtst - Track Car

      By Duncan · Posted

      Hope you aren't too sore after that one, might take a day or 2 to notice yet and I guess it is a loooooong drive home. On the bright side, tube frame front end is a thing at superlap, right?
    • Dose Pipe Sutututu
      R32 Gtst - Track Car

      By Dose Pipe Sutututu · Posted

      https://www.facebook.com/share/p/18rmVb1SKB/ 
    • GTSBoy
      Leak from Tokico BM50 Brake Master Cylinder

      By GTSBoy · Posted

      The chart of front pressure to rear pressure (with one being on the x axis and the other being on the y axis) is not a straight line on a typical proportioning valve. At lower pressures there is a straight line with one slope, and at higher pressures that changes to a lower slope. That creates a bend in the line at that pressure, called the knee point. If you do not change the proportionng as the pressure gets higher, you will suffer excessive pressure (at one end of the car or the other, depending on which way you look at the proportioning action) and then get lockups at that end. The HFM BM57, from my memory of previous discussions, is based on the BM57 from a different car (to a Skyline), with a different requirement for the location of the knee point and the distribution of pressure front to rear, and so is not a good choice for an upgrade on a Skyline. Here's a couple of links to some old posts, one from here, one from elsewhere. A lot of it pertains to adjustable prop valves, but the idea is the same. There are plenty of discussions on here about this issue from al the many years of people wanting a cheap/accessible option. https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/ https://grassrootsmotorsports.com/forum/grm/learn-me-brake-proportioning-valves/236880/page1/  
    • No Crust Racing
      R32 Gtst - Track Car

      By No Crust Racing · Posted

      Yeah dunno why johhny posted that here with no context, just post on FB/insta bro where he put it up?  Laine had an off at T4 during Thurs prac, he's ok, car is less than perfect, they are done for the weekend, he can fill in the rest. Bando also binned it like 100m up the road.   
    • MBS206
      R32 Gtst - Track Car

      By MBS206 · Posted

      I feel there must have been a FB/insta post and the weekend did not start well at all I hope everyone is all okay
×
×
  • Create New...