Jump to content
SAU Community

Recommended Posts

First post so take it easy.

I bought the mrs a series 2 33 which was pretty stock apart from slammed suspension and pod filter.

All i have done so far is a front mount intercooler.

i am getting a boost controller in the next few weeks.

What other reasonably cheap mods can i do to give it a bit more go?

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/
Share on other sites

In a nutshell (and I'm assuming it's a GTST, not a GTR, but it's worth you mentioning these things):

Forget about the boost controller at this stage

Do a full service if you don't know the status - oil, oil filter, air filter, coolant, plugs, check wiring

Think about a timing belt replacement if you don't know how old it is

If you do the timing belt, also replace the water pump, crank & cam seals, tensioner & idler pulleys

Test for boost leaks

New fuel pump for safety - if it's still got the original one it's around 20 years old

3" Turbo back exhaust, including high-flow cat

Z32 (300ZX) or R32 ECU plus a Nistune daughter board - this will allow a tuner to modify the factory tune

R32 Wastegate actuator (10 psi vs 5psi stock)

Get it tuned by someone who knows what they are doing - 210+ RWKW and a different car to drive

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7364960
Share on other sites

Cheers for that

It does have a 3" exhaust

front mount

and timing water pump etc have been done 60000km ago.

I was suprised drives better than a few cars i have driven lately that are less than 5 years old.

ECU is in the works as well as a tune.

The 32 wastegate actuator i take it is a stock item on the r32 and pretty easy to come by.

It is actually sounding quite cheap to do what i need.

Suspension will be the hard bit as at the moment its a bit to low and before to long i can see me or her leaving the front bar on a speed bump or something

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7364989
Share on other sites

I would strongly suggest avoiding Nistune with an R33. There are numerous other ECU's that will plug and play such as PoweFC (older tech) through to Adaptronic, Haltech, Link.

I would consider carefully what you want from the car as careful selection of parts in the first place will save you thousands. If you want more than 200rwkw then you are into the world of aftermarket turbos and new injectors. Each change will require more tuning so take your time to figure out realistically how you will use the car and how much power is needed to achieve it.

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7365015
Share on other sites

Cheers for that

It does have a 3" exhaust

front mount

and timing water pump etc have been done 60000km ago.

Is this going on the timing belt change info from its Japan days or has it been done in Australia? (kms get wound off in the importation process).

Is the 3" exhaust from the turbo back or just the cat convertor back? also does it have a higher flow cat?

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7365075
Share on other sites

If it's going to be a daily & you you don't want huge power I would stick with a Nistune. Others will tell you different, but a Nistune will do the job for you, as it does for me.

Yes - 32 wastegate actuater is stock on an R32, and is a direct replacement on an RB25Det. If you want more than 10psi you can leave the current boost solenoid installed, either in stock wiring or hot-wired to be always on higher boost. Note I haven't tried this - our solenoid has been removed.

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7365195
Share on other sites

There's a couple of points relating to the above post that need clarifying though.

If you use an R32 ECU to do Nistune then you don't get working VCT unless you install a separate way to switch it in and out. if you use a Z32 ECU for Nistune then a few other things don't work as well as they should. You need a decent tuner who has done these R33 Nistune jobs before to make it less painful.

If you use an R32 ECU then the stock boost solenoid cannot be controlled, because the R32 doesn't even have one.

R32 10psi actuators are not exactly lying around in piles, because every stock turbo R33 owner wants one.

Link to comment
https://www.sau.com.au/forums/topic/446752-r33-s2/#findComment-7365201
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • It is a kunfine Android screen . Does anyone know the wirering diagram of the fuga ??
    • just an update to this, poor man pays twice  Tried sanding down the pulleys but it didnt do the trick. Chucked another second hand alternator in the na car which I got for free off my mate and its fixed the squelling. Must have been unlucky with the bearings.    As for my turbo car, I managed to pick up a cwc rb alternator conversion bracket + LS alternator for 250 off marketplace, looked to be in really good nick. Installed it , started the car and its not charging the battery.... ( Im not good with auto elec stuff so im not sure if this was all I needed to do but I verified such by using a multimeter on the battery when the engine was running and I was only getting 12.2v )   I had to modify the earth strap for the new LS alternator , factory earth strap was a 10mm bolt which did not fit the bolt on the LS alternator which was double the size so I cut it off , went to repco bought some ring terminals that fit, crimped it onto the old earth strap and bolted it up to the alternator , started the car and same issue. Ran like shit and was reading 12.2 at the battery.  For a "plug and play" advertised kit thats not very plug and play but alas.  My question is , am I missing something ? Ive been reading that some people recommend upgrading the stock 80 amp alternator fuse to a 140 amp but I dont see how that would stop the alternator charging especially at idle not under load.  Regardless ive pulled it out and am going to get it bench tested by an auto elec tomorrow but it would be handy to know if ive missed something silly or have done something wrong.   
    • My wild guess is that you have popped off an intake pipe....check all of the hoses between the turbo and the throttle for splits or loose clamps.
    • Awesome, thanks for sharing!
    • To provide more specific help, more information is needed. What Android screen? What is its wiring diagram? Does the car's wiring have power at any required BAT and ACC wires, and is the loom's earth good?
×
×
  • Create New...