Jump to content
SAU Community

Have You Successfully Fitted A Raspberry Pi To Your Factory Tv/nav System


Recommended Posts

Has anyone actually hooked up a Raspberry Pi and been happy with the results.


Why I ask, is I have a 2005 stagea M35 with factory Nav/TV etc and connected my Raspberry Pi via the aux input at the factory TV tuner box in the rear left quarter.


I have tried two different ways to connect the Raspberry Pi, one via the analogue video output using RCA cable and 3.5 phone jack for sound out connected directly to the aux ( VTR ) input.


This gave me a good sound, but picture quality on the factory screen was fairly poor.


The other method was using HDMI output from the Raspberry Pi then via a HDMI to composite adaptor out to the aux ( VTR ) input again. Results again were much the same, good sound, but picture quality was average.


I'm using XBMC on my Raspberry Pi.


I would like to get this so the picture is of good enough quality that I can easily read the words on the screen without them being a little fussy and very small.


I guessing this may be a case of changing settings in the workings of XBMC maybe, but as of yet I have not managed to be able to change the screen resolution size to see any difference in what I see on the small car screen.


I know if I changed the screen to one that had HDMI input, that I would get a lot better screen picture, but I would think the factory screen would still give reasonable results.


Before anybody suggests taking my car to see who ever, I just wish to point out that I'm in New Zealand.


I'm happy to change any wiring, or direct link something into the factory tv tuner if that is needed.


Any help with this would be much appreciated.



Rotaman


  • Like 1
  • 1 month later...

I'm looking at this, but I am hoping to replace the screen with something more modern. the standard screen is 5.5" diagonal, which is an unusual size. Fitting a 4.3" would be easy but a backwards step in size. 7" seems just a bit too big to make it fit.. and there's not really anything in between.

otherwise if you can get a decent result with the factory screen, it's a good size so i'd be happy to leave it. haven't tried pulling mine apart yet. I'm on the lookout for a spare TV unit to try replacing the screen as above.. don't feel like leaving a hole in my dash while I mess around :P

where does the composite video input plug in for the screen?

Geoff,

Screen is a sharp or Panasonic in the m35 from memory.

It needs a data feed to fire it as there are 4 inputs that need to be setup.

The 34 is a 5.8" unit and easier as it is a sharp unit. I have the datasheet for that one and if you can generate RGBS then you are on your way. That unit is a twin input with a logic trigger to select it.

This is a later motorized screen. Similar idea. Toshiba supplied. The board supplies all of the signals to run it.

post-2209-0-09028200-1417336306_thumb.jpg

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...