Jump to content
SAU Community

Recommended Posts

Hey guys. So basically I was driving around and stopped at a set of lights and suddenly smoke vapour appeared out of my steering column (the plastic surround) this happened a few weeks ago once and just recently it happened again.

My indicator works but as soon as the flashing arrow is off I can still hear the indicating noise! Could this be the reason why there was a bit of smoke? A fuse screwed up? The car is a r33 gts25. The car has been driving fine and all other electronics work, the car also has an alarm system that utilizes the indicator bulbs when you lock and unlock the car, could this be another reason? Many thanks.

Edited by TommyR33

Take off the steering column covers. (Couple screws, piece of piss)

Look around all your wiring looms. Especially places where splices have been made.

The biggest give away is electrical tape. All the wiring is pretty well in your face once the covers come off.

The smoke may be coming from further down in your footwell and the smoke is just making its path up and away out of your steering column section

When you say you can still hear the indicator noise is that permanantly or stays on for a little while?

It definitely sounds electrical. Do you have an aftermarket turbo timer in the car?

Has the person who installed the car alarm made proper electrical terminations or just twist a twist and tape job.

It probably wouldnt hurt to double check all your fuses too.

More of a look and discover type thing really. With any electrical fault be careful though. No one likes shorting out wires and blowing up the pcb to your mongoose alarm hahaha

Take off the steering column covers. (Couple screws, piece of piss)

Look around all your wiring looms. Especially places where splices have been made.

The biggest give away is electrical tape. All the wiring is pretty well in your face once the covers come off.

The smoke may be coming from further down in your footwell and the smoke is just making its path up and away out of your steering column section

When you say you can still hear the indicator noise is that permanantly or stays on for a little while?

It definitely sounds electrical. Do you have an aftermarket turbo timer in the car?

Has the person who installed the car alarm made proper electrical terminations or just twist a twist and tape job.

It probably wouldnt hurt to double check all your fuses too.

More of a look and discover type thing really. With any electrical fault be careful though. No one likes shorting out wires and blowing up the pcb to your mongoose alarm hahaha

Thanks so much for the help! Basically what happens is I indicate and when it switches off the ticking sound stays on and almost at a faster rate of interval ticks. I went under near the footwell and fiddlled around with the plug that goes into the indicator box and now its stopped and is fine! I am no auto electrician Mick but there is electrical tape in many spots and some wires and plugs bunched up not connected into anything, I mean it all looks neat but yeah. Maybe get a auto electrician to have a look for me.

I had this exact issue on my '94 Bluebird.

Turned out to be inside the stalk, a small piece of plastic between 2 copper terminals had broken / melted so it was arching between them.

A small ziptie strategically positioned and trimmed down, with a spot of superglue on it, Fixed it better than new. :)

All good mate, happy to help. If you do decide to look into any connection further please do disconnect the ground from the battery. Forgot to say that but it pays off to be careful haha.

auto-elec might charge you an arm and a leg for small amounts of work but sometimes piece of mind is worth it.

I can save you the trouble of further investigation. It's the blinker mechanism. I've gone through two of them. Once the blinker stalk smokes it's finished. There must be something about the inner workings that fails and causes a short. Get a 2nd hand one and away you go. A new one would be even better.

Something that may interest you is the blinker relay under the dash. A square box with three wires. That's where your ticking comes from, quite normal. Be aware that the relay can go from time to time and may have been replaced by a universal relay. Some relays are 2 wire and others 3, one being an earth. Replace the relay with an original 3 wire relay and a new stalk, problem fixed. I did it myself but an auto electrician will put it in for you cheap.

Read the tutorial to remove the column cover and remove the screws holding the stalk. I can't remember what else there is as it hasn't needed replacing for years.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Who did you have do the installation? I actually know someone who is VERY familiar with the AVS gear. The main point of contact though would be your installer.   Where are you based in NZ?
    • Look, realistically, those are some fairly chunky connectors and wires so it is a reasonably fair bet that that loom was involved in the redirection of the fuel pump and/or ECU/ignition power for the immobiliser. It's also fair to be that the new immobiliser is essentially the same thing as the old one, and so it probably needs the same stuff done to make it do what it has to do. Given that you are talking about a car that no-one else here is familiar with (I mean your exact car) and an alarm that I've never heard of before and so probably not many others are familiar with, and that some wire monkey has been messing with it out of our sight, it seems reasonable that the wire monkey should be fixing this.
    • Wheel alignment immediately. Not "when I get around to it". And further to what Duncan said - you cannot just put camber arms on and shorten them. You will introduce bump steer far in excess of what the car had with stock arms. You need adjustable tension arms and they need to be shortened also. The simplest approach is to shorten them the same % as the stock ones. This will not be correct or optimal, but it will be better than any other guess. The correct way to set the lengths of both arms is to use a properly built/set up bump steer gauge and trial and error the adjustments until you hit the camber you need and want and have minimum bump steer in the range of motion that the wheel is expected to travel. And what Duncan said about toe is also very true. And you cannot change the camber arm without also affecting toe. So when you have adjustable arms on the back of a Skyline, the car either needs to go to a talented wheel aligner (not your local tyre shop dropout), or you need to be able to do this stuff yourself at home. Guess which approach I have taken? I have built my own gear for camber, toe and bump steer measurement and I do all this on the flattest bit of concrete I have, with some shims under the tyres on one side to level the car.
    • Thought I would get some advice from others on this situation.    Relevant info: R33 GTS25t Link G4x ECU Walbro 255LPH w/ OEM FP Relay (No relay mod) Scenario: I accidentally messed up my old AVS S5 (rev.1) at the start of the year and the cars been immobilised. Also the siren BBU has completely failed; so I decided to upgrade it.  I got a newer AVS S5 (rev.2?) installed on Friday. The guy removed the old one and its immobilisers. Tried to start it; the car cranks but doesnt start.  The new one was installed and all the alarm functions seem to be working as they should; still wouldn't start Went to bed; got up on Friday morning and decided to have a look into the no start problem. Found the car completely dead.  Charged the battery; plugged it back in and found the brake lights were stuck on.  Unplugging the brake pedal switch the lights turn off. Plug it back in and theyre stuck on again. I tested the switch (continuity test and resistance); all looks good (0-1kohm).  On talking to AVS; found its because of the rubber stopper on the brake pedal; sure enough the middle of it is missing so have ordered a new one. One of those wear items; which was confusing what was going on However when I try unplugging the STOP Light fuses (under the dash and under the hood) the brake light still stays on. Should those fuses not cut the brake light circuit?  I then checked the ECU; FP Speed Error.  Testing the pump again; I can hear the relay clicking every time I switch it to ON. I unplugged the pump and put the multimeter across the plug. No continuity; im seeing 0.6V (ECU signal?) and when it switches the relay I think its like 20mA or 200mA). Not seeing 12.4V / 7-9A. As far as I know; the Fuel Pump was wired through one of the immobiliser relays on the old alarm.  He pulled some thick gauged harness out with the old alarm wiring; which looks to me like it was to bridge connections into the immobilisers? Before it got immobilised it was running just fine.  Im at a loss to why the FP is getting no voltage; I thought maybe the FP was faulty (even though I havent even done 50km on the new pump) but no voltage at the harness plug.  Questions: Could it be he didnt reconnect the fuel pump when testing it after the old alarm removal (before installing the new alarm)?  Is this a case of bridging to the brake lights instead of the fuel pump circuit? It's a bit beyond me as I dont do a lot with electrical; so have tried my best to diagnose what I think seems to make sense.  Seeking advice if theres for sure an issue with the alarm install to get him back here; or if I do infact, need an auto electrician to diagnose it. 
    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
×
×
  • Create New...