Jump to content
SAU Community

Recommended Posts

Hey guys. So basically I was driving around and stopped at a set of lights and suddenly smoke vapour appeared out of my steering column (the plastic surround) this happened a few weeks ago once and just recently it happened again.

My indicator works but as soon as the flashing arrow is off I can still hear the indicating noise! Could this be the reason why there was a bit of smoke? A fuse screwed up? The car is a r33 gts25. The car has been driving fine and all other electronics work, the car also has an alarm system that utilizes the indicator bulbs when you lock and unlock the car, could this be another reason? Many thanks.

Edited by TommyR33

Take off the steering column covers. (Couple screws, piece of piss)

Look around all your wiring looms. Especially places where splices have been made.

The biggest give away is electrical tape. All the wiring is pretty well in your face once the covers come off.

The smoke may be coming from further down in your footwell and the smoke is just making its path up and away out of your steering column section

When you say you can still hear the indicator noise is that permanantly or stays on for a little while?

It definitely sounds electrical. Do you have an aftermarket turbo timer in the car?

Has the person who installed the car alarm made proper electrical terminations or just twist a twist and tape job.

It probably wouldnt hurt to double check all your fuses too.

More of a look and discover type thing really. With any electrical fault be careful though. No one likes shorting out wires and blowing up the pcb to your mongoose alarm hahaha

Take off the steering column covers. (Couple screws, piece of piss)

Look around all your wiring looms. Especially places where splices have been made.

The biggest give away is electrical tape. All the wiring is pretty well in your face once the covers come off.

The smoke may be coming from further down in your footwell and the smoke is just making its path up and away out of your steering column section

When you say you can still hear the indicator noise is that permanantly or stays on for a little while?

It definitely sounds electrical. Do you have an aftermarket turbo timer in the car?

Has the person who installed the car alarm made proper electrical terminations or just twist a twist and tape job.

It probably wouldnt hurt to double check all your fuses too.

More of a look and discover type thing really. With any electrical fault be careful though. No one likes shorting out wires and blowing up the pcb to your mongoose alarm hahaha

Thanks so much for the help! Basically what happens is I indicate and when it switches off the ticking sound stays on and almost at a faster rate of interval ticks. I went under near the footwell and fiddlled around with the plug that goes into the indicator box and now its stopped and is fine! I am no auto electrician Mick but there is electrical tape in many spots and some wires and plugs bunched up not connected into anything, I mean it all looks neat but yeah. Maybe get a auto electrician to have a look for me.

I had this exact issue on my '94 Bluebird.

Turned out to be inside the stalk, a small piece of plastic between 2 copper terminals had broken / melted so it was arching between them.

A small ziptie strategically positioned and trimmed down, with a spot of superglue on it, Fixed it better than new. :)

All good mate, happy to help. If you do decide to look into any connection further please do disconnect the ground from the battery. Forgot to say that but it pays off to be careful haha.

auto-elec might charge you an arm and a leg for small amounts of work but sometimes piece of mind is worth it.

I can save you the trouble of further investigation. It's the blinker mechanism. I've gone through two of them. Once the blinker stalk smokes it's finished. There must be something about the inner workings that fails and causes a short. Get a 2nd hand one and away you go. A new one would be even better.

Something that may interest you is the blinker relay under the dash. A square box with three wires. That's where your ticking comes from, quite normal. Be aware that the relay can go from time to time and may have been replaced by a universal relay. Some relays are 2 wire and others 3, one being an earth. Replace the relay with an original 3 wire relay and a new stalk, problem fixed. I did it myself but an auto electrician will put it in for you cheap.

Read the tutorial to remove the column cover and remove the screws holding the stalk. I can't remember what else there is as it hasn't needed replacing for years.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...