Jump to content
SAU Community

Recommended Posts

Long story short is my rear window washer motor stopped working 6 months ago and then my front window washer 1 month ago.

Step by step guide to fix the issue:

Time: 20 minutes to an hour, 2 days to completely re-install and operate.

Tools: Socket set, test light, Multi-grips, WD40, Silicon sealant, steak knife, tooth picks, cotton buds, scourer, rags

Check to see if there is power to the washer motors which are located in the front of the washer bottle.

1. Pull the electrical plugs and use a test light. Ignition on and get someone to fire up the washers from the stalk. In my case had power to both plugs so I cleaned the connectors on the motors plugged them back in and tried again. No luck so the motors had seized. If you have no power with your test light check the fuses i suppose.

Removing the motors:

1. Take the washer bottle out with 10mm socket on the 2 screws. Pull the electrical connector. Lift the bottle.

2. Tip the bottle so the pumps are facing up and disconnect the tubing. Don't disconnect the tubing with the bottle in its normal position or water will leak everywhere.

3. Take the bottle out and tip out the water.

4. The motors are held in place by rubber grommets so just pull the motors in different angles to pries them free.

5. Motors are out.

post-89815-0-25516500-1417613256_thumb.jpg

Taking the motors apart and getting them to work again

So the motors are basically plastic cylinders with a brush electrical motor in it that spins an impeller that pushes water into the washer pipe. So its not spinning, so lets have a look.

1. The plastic case has 2 ends that are removable. I tried to pry it open but couldn't so i just started cutting with a knife and then i could get them off.

post-89815-0-47610400-1417613366_thumb.jpg post-89815-0-80135800-1417613415_thumb.jpg

2. The bottom of the motor has the impeller (where the water outlet is), the top has the guide for the shaft of the armature.

post-89815-0-25841500-1417613515_thumb.jpg post-89815-0-69315100-1417613591_thumb.jpg

3. I then tried to spin the impeller with my fingers and it was locked then i gently turned the shaft and impeller and got some movement but there was a lot of resistance. we have found the problem.

post-89815-0-06471700-1417613721_thumb.jpg

4. Use the tip of a knife to take the impeller off (gently).

5. At the other end use multi-grips on the shaft and pull and twist to free the armature from the magnets and take the armature out.

post-89815-0-10479700-1417613828_thumb.jpg post-89815-0-09405100-1417613894_thumb.jpg

6. So you are left with a pretty dirty motor in pieces. Time to clean

post-89815-0-21939500-1417614042_thumb.jpg post-89815-0-40904000-1417614260_thumb.jpgpost-89815-0-87514500-1417614330_thumb.jpg

7 If you look in you will see the contacts and at the base is where the armature shaft contacts the guide..... filth.

post-89815-0-83136600-1417614470_thumb.jpg

8. Using tooth picks, cotton buds and WD40 I rubbed and cleaned everything I could see. Especially the magnets, armature coils (use scourer), and other contact points. Use the toothpicks to move the contacts out of the way to get to the bottom support which is usually filthy. A note, dont use steel wool as the filings might attach to the magnets and cause issues with the armature.

post-89815-0-62716700-1417614687_thumb.jpg

9. All clean.

post-89815-0-51547900-1417614912_thumb.jpg post-89815-0-86344800-1417614991_thumb.jpg

10. Now time to put it back together. Slide the armature back in and carefully slide the shaft in between the contacts, push a bit so it goes into the home position and put the top back on. Make sure the shaft is in the guide and tape the top cover down to hold it in.

11. Put the impeller on the shaft the right way (flat side out and line up the flat edge on the shaft). Spin the impeller with your fingers and admire how freely it spins. Now put the end back on and tape it on.

post-89815-0-19935800-1417615128_thumb.jpg

Testing the operation of the motor

Now its time to see if it works

1. With a taped up motor go back to the car and connect the motor to the connector and fire up the washers from the stalk. Listen to the music as your motor buzzes away. Just like new.

post-89815-0-86407300-1417615206_thumb.jpg

Resealing the motor

Need to reseal the motor with bathroom silicon sealant. Just pull an end off at a time and apply some sealant with your finger where the cap mates with the cylinder edge and put it back on. Don't get any inside as it could foul the motor as it spins.

post-89815-0-58696800-1417615236_thumb.jpg

Then rub some sealant around the edge it to seal it. Then do the other end.

post-89815-0-71710700-1417615273_thumb.jpg

Then let them sit for 2 days and re-install everything.

post-89815-0-67388300-1417615313_thumb.jpg

Just a hint with the washer bottle re-installation is that it has a small lip the fits under a little mount on the drivers side edge, so put this in first then do the 2 screws up.

Fill it up with water and admire your work.

Done

Hope this helps....cheers

  • 4 weeks later...
  • 4 weeks later...

Good job. I should try this next time.

Another trick i have tried is reversing the polarity on the motor back and forward and after a few goes it will start spinning.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...