Jump to content
SAU Community

Rb25de Bracket Locations, Help Needed, Pictures Included!

Hanzie

By Hanzie,
in General Maintenance

 Share

Recommended Posts

Hanzie Enthusiast

Hanzie

Posted
Posted

Hey, i have just finished installing a new head gasket for the first time on this engine, i am about to install the intake plenum and air ducting, but i still have these 4 brackets left to attach, im not sure where abouts they go, and i dont want to put the plenum on before putting the brackets on, if someone could point me in the right direction that would be helpful, if possible could someone post pics?

post-112300-0-57298100-1420270617_thumb.png

Aggroman Grand Master

Aggroman

Posted
Posted

top left and bottom right attach to the lower side of the intake plenum..

Bot right is central holding knock sensor cable and attaches to the big part of the loom

top left goes near firewall, the little notch against the plenum it should be straight forward from there

Aggroman Grand Master

Aggroman

Posted
Posted

bottom left goes on the manifold as part of the heat shield.

My advice is to put the lower half on and connect what you can... If you look at the bottom half you will see all the associated holes with thread in them, they almost line themselves up when you do it all.

Looking at it again I think the top left one goes towards the front end and holds the grey injector loom plug and helps with the TPS wiring and such

Hanzie Enthusiast

Hanzie

Posted
  • Author
Posted

Do you mean the bottom right goes towards the injector loom and tps wiring? And top left goes on the plenum? I just wanna make sure cause I think you may have meant to say bottom left instead.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...