Jump to content
SAU Community

Recommended Posts

Just this last week I've noticed my clutch pedal start to make an annoying amount of noise. I've tried spraying the moving parts in the cabin, but with no change. Its not even a normal squeak, more of a metal bending / clunking noise.

I thought it was best to make a quick video to show, but for some reason SAU always freezes if I try to add a URL or pics. Instead, please search YouTube for the following...

ECR33 skyline noisy clutch pedal

It will be the first one, 22 seconds long. Usually there is no noise when using the clutch, but as you can see in the vid there is quite a bit.

Any ideas why and what the fix is?

Would this be something that would be fixed by installing a NISMO reinforced clutch pedal, but some form of maintenance or parts replacement?

Any help is much appreciated.

Thanks

If the pin is worn, you could buy a replacement, or you could weld it up and turn it back down. If the hole in the bracket or pedal is worn eccentric then you could buy a Nismo bracket or you could drill it out and bush it, weld it up and redrill, etc etc etc.

I got down and had another look but couldn't tell where the noise was coming. I might try replacing the pin first and hope that's is at its cheap. Its a right PINA doing anything on under dash tho

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • You’ll be very upset when you bust that too not to mention the gearing totally sucks. Don’t do it.
    • Is the panel filter one that is oiled? Have you ever cleaned or touched the AFM?
    • So.... the K&N air box thingo was too big, ended up gifting it to a mate, well, by gifting it he actually supplied food and beer at the pub,  which was nice, as it will not sit on a shelf in the garage for the next 10 years I did trim up some of the existing stuff to neaten it all up and gave it some wrinkle paint, unfortunately it currently has a used and abused mish mash of different types of hose clamps, 4 big fat T bolt type (shit), and a few normal clamps of vairing sizes and brands, but..... only until the 6 constant tension black worm clamps that I ordered from EFI solutions turn up next week Currently the current hose clamps are triggering me hard, LOL Is this the final version, probably not, I really want just 2 silicone pieces, a straight bit of silicone from the filter to the MAF is easy and will happen as soon as I head into Just Jap tomorrow, the problematic part is a 30° silicone bend from the MAF to the TB that I can connect the engine breather from the head, I found that there are bulk head fittings for boat bilge pumps that should work, but until I can get a 30° silicone bend the alloy pipe, and the 11ty thousand hose clamps, are there for the foreseeable future 4 hose clamps are golden, 6 are grudgingly acceptable, the 8 currently holding it all together is just taking the piss    I've also ordered 60 more retaining wall blocks for the front yard, I mis-gonculated the height that was required to get above the base of the Photinia's (red robin's) that are the hedge behind the front fence, currently it is 2 blocks high, and about 1/2 a block short, so going 3 blocks high will be above the base of the red robin's, and allow some room for mulch
    • It is the stock air box with the panel filter. Everything else is stock except the exhaust at this point, as I also went back to the cleaned 270cc injectors. I will check the RPM when the IACV is unplugged and report back.
    • As MBS suggested if this is happening when the engine is cold you're going to want to remove the intake air regulator and verify resistance + that the shutter is physically opening and closing. At -20C should be fully open, 20C half open, over 60C fully closed. At 20C should be 70-80 ohms. For AAC valve testing using a Consult cable see if you can raise and lower the idle by commanding more or less AAC duty cycle. Hopefully it's pretty linear as well, shouldn't be like 30% AAC valve is barely idling and 40% is 1500 rpm.
×
×
  • Create New...