Jump to content
SAU Community

Recommended Posts

lights dim cause of the current the amp draws. but mine does that also Alpine amp most newer good amps have clipping protection to stop cookin ur sub and amp. best bet is to turn it down at the amp, mine cuts out still if i crank it really high. u just need to find the right balance took me 8months in my lancer before i was happy than sold it and brought a system for my mr2 happy with it for now seeming cant get to big a stereo in here

hrmm, try putting all the eq's flat on the headunit, gain on the amps low, and even the freq cut off low. than set those low/high/flat thingos if u got them

than turn ur headunit to 3/4 or 4/5 of the way up than adjust ur cross overs on the amp than adjust the gain up slowly just before clipping. thats how i tune mine and works most the time.

and im not pissed with you cause u gotta r34 :rant: i tune ur stereo u give me ur car deal?? hehe

Maybe the amp just doesn't have enough power to run your sub then? Sounds to me like your overdriving the amp

Driver came into irc chat and asked the same question, and my response was the same as ferni's.... with an analogy that "it's the same as asking us 'why is my room dark' and then not telling us how many lights are in the room, or how many watts the globes are"

In order to diagnose this problem, we need to know the following:

1/ What sort of sub

2/ What sort of amp

3/ What sort of car battery

:rant:

  • 2 weeks later...

Get yourself a 1 Farad cap.

The current draw from the Sub amp is sucking too much power and the amp is protective itself.

Same thing happened in my Calais.

The Cap gives the Amp the stored instant energy it needs.

BASS OUT

bass junky nailed it for you mate, your amp quite simply draws too much current from the battery at one particular moment, and the battery can't give the amp the current it needs at that one particular moment, which results in the amp going into safety mode and your bass cutting out....

i would recommend getting a capacitor as well as they stop yours amp cutting out by supplying a constant power to the amp

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Have you done the Ignition Sync Wizard in the AEM software?
    • Find out what RPM it was idling at with the IACV unplugged. It's very weird that the rpm didn't change at all, and then it stalled. When it stalls is it nearly like a switch off, like you've turned the engine off? Or is it more stutters and sputters and coughs to death over a few seconds? Or does the RPM just slowly keep going down and down? Have you done a test of trying to start it with the AFM unplugged? Does it still die?     If you Follow Josh's advice on using Nistune to check the voltages (which is a perfect method!) if you see anything out of wack voltage wise, THEN get the multimeter out and read the voltage directly at the sensor. If the two vary, then you're now looking for a wiring issue vs a sensor issue. So be aware, what the ECU sees, may not be what the sensor is actually saying too...
    • You very likely need to get it on a dyno and tune it. My assumption is, you've got an RB25DET tune in it, which has a different manifold, different injectors, and different cams as a minimum. What O2 sensor are you running?   When you say it runs extremely rich from idle all the way to redline, is this just free revving it you see that?
    • I seem to the be only person that is using a Haltech 2500 on an NA motor, I've installed a Bosch DBW throttle body to the OEM intake manifold and am having problems maintaining AFR even with the wideband o2.  It will run extremely rich at idle and up to redline, but under load it will go extremely lean in the 20s and i'm essentially having to rev it over 4k and feather the clutch to get it up to speed.  I've read a few other threads of about the butterfly, it seems removing the vacuum to it is supposed to have it remain open, i've noticed no difference under 4k with the vacuum line to it plugged.  I'm hoping someone here has had luck using the NA manifold with Haltech, and if they happen to have a tune for it.  
    • I don't know any details, but I really wouldn't be surprised if they do it as a LHD only version, at least initially.
×
×
  • Create New...