Jump to content
SAU Community

RB Light Weight Flywheels $375


Recommended Posts

  • Replies 66
  • Created
  • Last Reply

Top Posters In This Topic

4340 is perhaps the highest grade high tensile steel that most machine shops can machine!!! THe japanese ones that are below 5 kgs are a totally different kettle of fish they are billet cast then machined (very expensive)... Also all you guys wanting to go below 5 kg have you thought of the effect on MAIN bearingS when doing this and not haveing the crank balanced; as you would in a rebuild.... Word of warning!! Going to light would be detramentle...

free bump!!!they sound good pity i have a tripple plate!!

nice price on the flywheel.

The comment about going below 5kg on a balanced flywheel causing any kind of damage to bearings is rubbish however. You should retract the statement for fear of scare mongering for business, a tactic I'm sure you are not advocating.

I'd like to point out that 6kg odd is still alot lighter than factory stock and for those who don't have $500+ to spend on a lighter unit it offers a cheap but, very significant performance increase.

the flywheels are CNC machined but are they also balanced at a significant rpm?

Guest darrinspencer
If you can't get 10 people, are we still able to get them even if its a bit more?

Ok

We can buy 6 now for $375 each at the same price as before

The group buy will remain open to try and sell the other 4.

The company is getting 20 made at the moment and they will be ready in 2 weeks

I will PM all people who wanted one and arrange payment once they are ready to ship.

Sky30: It depends on who you listen to. From my understanding, after fitting the flywheel the following is true:

- Torque will decrease, thanks to less inertia , due to less mass on the moving flywheel.

- The engine will rev faster, thus generating exhaust gas more quickly, thus spooling up the turbo faster. (This is faster in time, not faster as in lower rpm point) Unknown exactly how faster it'll rev... depends on load and enviroment, etc.

Guest Robo's

Ive been Reading abit about these, apparently its like dropping the weight by about 100kg in first gear, so you could imagine the accelaration. It takes less effort to run. The motor will spin freer, but noticeably idle a little rougher if you go too light.

Theres a couple of good reads on the net on these. Do a search!!

They're a wee bit of a trade off... lose a bit of torque down low, but who the hell cares because you're into the meaty power/torque zones faster, so it's all good. :)

If you really care about torque (as we all really should), do a 3L conversion or put some cams in.

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • By popular demand.. it was a coil. Got my hands on 1 new OEM coil, replaced with the one that made the less noise difference when I unplugged it while the car was running and started the car up. No stutter and the engine light was gone. I guess I’ll buy the other 5 they have lol
    • No, code 21 is very straightforward. It can only be the things described in that diagnostic flow. In fact it has no way of knowing that the spark plug resistance is out of spec.
    • Hi, SteveL Thank you very much for your reply, you seem to be the only person on the net who has come up with a definitive answer for which I am grateful. The "Leak" was more by way of wet bubbles when the pedal was depressed hard by a buddy while trying to gey a decent pedal when bleeding the system having fitted the rebuilt BM50 back in the car, which now makes perfect sense. A bit of a shame having just rebuilt my BM50, I did not touch the proportioning valve side of things, the BM50 was leaking from the primary piston seal and fluid was running down the the Brake booster hence the need to rebuild, I had never noticed any fluid leaking from that hole previously it only started when I refitted it to the car. The brake lines in the photo are "Kunifer" which is a Copper/Nickel alloy brake pipe, but are only the ones I use to bench bleed Master cylinders, they are perfectly legal to use on vehicles here in the UK, however the lines on the car are PVF coated steel. Thanks again for clearing this up for me, a purchase of a new BMC appears to be on the cards, I have been looking at various options in case my BM50 was not repairable and have looked at the HFM BM57 which I understand is manufactured in Australia.  
    • Well the install is officially done. Filled with fluid and bled it today, but didn't get a chance to take it on a test drive. I'll throw some final pics of the lines and whatnot but you can definitely install a DMAX rack in an R33 with pretty minor mods. I think the only other thing I had to do that isn't documented here is grind a bit of the larger banjo fitting to get it to clear since the banjos are grouped much tighter on the DMAX rack. Also the dust boots from a R33 do not fit either fyi, so if you end up doing this install for whatever reason you'll need to grab those too. One caveat with buying the S15 dust boots however is that the clamps are too small to fit on the R33 inner tie rod since they're much thicker so keep the old clamps around. The boots also twist a bit when adjusting toe but it's not a big deal. No issues or leaks so far, steering feels good and it looks like there's a bit more lock now than I had before. Getting an alignment on Saturday so I'll see how it feels then but seems like it'll be good to go       
×
×
  • Create New...