Jump to content
SAU Community

Recommended Posts

Located Gold Coast will freight all parts auswide

Gearboxes r32 push type $500

R32 pull type late model $750

R33 pull type $800

R33 converted to r32 manual speedo drive and push bell housing $850

N1 headlights with grill brackets $500

-5 twin turbos $1600 only 1200km use absolutely perfect cond.

Dash pad $160 perfect demister vents no ac vents (passenger and middle vent available for $120pair) or $260 the lot whole dash VGC

Gtr fuel tank plastic with walbro pump and sender $200

Cluster surround and working clock $180

Drivers door switch $70

Centre gauges $70

Steering surround $20

Telescopic part $20

Twin turbo pipe in black both pipes and hose $100

Abs $150

Latch and support with horns $70

Stainless dumps brand new $100

Mines stainless dumps and front pipe $600 3" bell mouth type

Rear seat good cond. $100

Rear subframe $100 bare

Spare wheel $50 genuine jdm r32 gtr

Rear door cards $100 pair

785cc injectors billet rail Turbosmart reg with -6 braided line $500

Textured stereo surround $80, ashtray $40, manual surround $40 boot $10 or $180 the lot

Drivers window relay $50

Heater vent actuators $50ea both available

Gtr r32 brakes and cross drilled rotors $200

Plenty more parts available preferably text or call to discuss 0414596256 more photos available also

post-44496-14240410126628_thumb.jpgpost-44496-14240410293949_thumb.jpgpost-44496-14240410570334_thumb.jpgpost-44496-14240410737196_thumb.jpgpost-44496-14240411098878_thumb.jpgpost-44496-14240411281251_thumb.jpgpost-44496-14240411425313_thumb.jpgpost-44496-14240411664365_thumb.jpgpost-44496-14240411922718_thumb.jpg

Link to comment
https://www.sau.com.au/forums/topic/453896-for-sale-r32-gtr-wrecking/
Share on other sites

  • Replies 40
  • Created
  • Last Reply

Top Posters In This Topic

Is the textured stereo surround in good condition with no cracks or scratches and all clips?

Can you send a pic?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...