Jump to content
SAU Community

Recommended Posts

Hey all! I have been thinking of upgrading the suspension in my R33 for a while now and I think the time has come.

A good deal has come up on a used set of BC BR coilovers for $800 the owner said they would probably have about 10,000k's on them and they have been used in his street car..

I was just wondering if I could get some opinions on buying second hand before I think about dropping the cash on them or if I should just buy brand new.

Cheers

Link to comment
https://www.sau.com.au/forums/topic/454678-buying-second-hand-coilovers/
Share on other sites

I'd want to remove/inspect the upper spring retainer/top hat. Check for play in pillow ball.

Next remove springs and check damper for scoring or pitting on damper rod. Also check dust seals (you won't be able to see oil control seals). Any dampness = bad.

Compress the damper and check for squelching or bubbling sounds. Also check lateral free-play of damper rod. Ensure damper rebounds to full length without assistance.

Check all adjusters through their range of motion.

For $800 I'd be so much more inclined to shell out an extraa $400 and get new ones.

I simply said that for 800 bucks I wouldn't be buying second band BC.

When I bought mine I went through Aaron at import monster and he imported a great set of RA teins for me

I got these for 600 delivered from Japan. Like new

post-47556-0-26727600-1426558151_thumb.jpg

I just sold a set of used Cusco coilovers for $200. One was known to be leaking, rest felt ok on the car (note my ad clearly stated that they needed a rebuild). That's realistically all second hand coilovers are worth unless you know the history of them.

I might pay $800 for a set of MCA gold second hand (even though they'd be thrashed to death on a rally car) because they can be completely rebuilt, and they are top notch gear to start with.

If you can get coilovers new for $1100, then second hand ones are not worth anywhere near 50% of that price, unless as I stated you can prove their history and condition.

A few years ago I bought some second have JDM spec "Ohlins" PCV coilovers for a little over $1000 shipped from Malaysia. Worked great for a while, until the pillow balls started knocking. I would have had them rebuilt but my Skyline (un)fortunately was written off by a flood before I had the chance

If I had to do it again, I'd spend the money on brand new MCAs or a just a Eibach/Bilstien combo... Something that I know for sure can be rebuilt. Heasmans told me that some JDM Ohlins can't be rebuilt, which is a shame for a set of coilovers that go for around $3000 plus shipping brand new!

Thanks for the feedback everyone! I will wait a bit longer, save some more coin and buy them brand new which will give me piece of mind knowing that I might not be buying someone else's problem and that they will have warranty :yes:

  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Take the value it measured as, and pick the closest range available that is above the reading on the screen.   Also, no point just testing the coils. Read what has been said again. You need to test all your wiring, everything.
    • Does the scanner do all the CUs in the car, or only the ECU?
    • @666DAN sorry to bring you and old thread.     I've got my de+t done and it's all running great other than 1 small issue.    Car has remained auto with the na auto and tcm, I've used a stagea ecu with. NIstune board and everything is great other than my gear selection on the dash. It illuminates park, reverse, neutral, 3rd and 2nd when selected . But nothing when in  drive or what gear your in when you pop it into tiptronic. I'm sure there is maybe 1 wire in the ecu plug I need to move to rectify this. Do ya have any ideas?     Cheers man
    • Well I recently changed my rear axles and was thinking if I bumped anything, I have been driving the car for a while now though... But it has been raining today so everything is wet under the wheel arches. Brakes feel fine and can't hear any of the metal screamers, I had a squeak coming from one of the handbrake drums but that seems to have gone away a while ago. I was going down a hill when it lit up and I did feel the abs bite for a second and question why it did it?
    • Correct. Um. I dunno. I haven't cared enough about the way that the NA cars work to know for sure. But..... The 33/34 turbo manual cars have an electronic speed sensor in the gearbox that outputs a +/- (ie, sawtooth AC) voltage signal. That is connected to the speedo. The speedo then outputs a 0-5v square wave (ie, PWM) signal that the ECU (and any other CU on the bus) sees. The speed sensor is NOT directly connected to the ECU. So here's the problem. Your new ECU expects to see the PWM signal, but must somehow be getting a direct signal from the diff speed sensor. Which would suggest that the wiring of the NA car is not the same as the turbo cars. I think you will need to spend some time with (hopefully the wiring diagram for the car) and a multimeter to see what is connected to what. Then, presuming I am correct**, you would then want to separate the ECU speed signal input from the rest of the car's wiring, and probably either buy a speed signal converter, or build one using an arduino (or similar). That would take in the speed sensor signal and output a scaled (and suitably rearranged) signal for the ECU. ** We shouldn't presume that I am correct here, because there might be something else crazy going on. I don't think you could convert the speedo to be fed from the gearbox sensor, because the pulse rate from that sensor is probably different to the diff sensor and then the speedo would read wrongly. And this also wouldn't fix the ECU's problem either, because the ECU doesn't want to see the gearbox signal direct either (assuming that they are all on the same wiring, for some odd NA related reason, see above caveat!) Does this help? Probably not. Can you make it work? Almost certainly. With the above work. You should buy a handheld oscilloscope from Aliexpress so that you can view these signals directly. Connect up the probes and drive the car. Show photos of the screen when drving at known speeds and connected to different places, and we'll see what we can learn about it.
×
×
  • Create New...