Jump to content
SAU Community

Recommended Posts

Was about to say the same as Ben ^..... try some rims that fit without the adapter

that means i need borrow set of nissan stock rims....

i just changed the position between front wheels and rear, let's see on Monday.

Or take it pedders for the steering and suspension check. Im pretty sure if you took it to the tire place and get them to look at it. Im sure when you explain it to them they will know whats wrong with it. Better then going back an forward on a forum arriving and no answer is it not.

the hub adapters are brand new. I bought the hub adapters because the vibration problem, but the problem didn't get sorted.

So car drives fine.

Starts vibrating.

You buy hub adaptors.

Is that what happrned or something else inbetween?

So car drives fine.

Starts vibrating.

You buy hub adaptors.

Is that what happrned or something else inbetween?

1. my car has vibration problem when i bought it

2. I did 4 wheels balance, and changed 4 brake rotors

3. bought new rims with previous tyres and balanced

4. bought hub adapters

5. just rotate the wheels between front and rear

still has the problem.

i record a video here, you can here some noise from 20s - 24s when I accelerate the car (around 50-70 km/h) and the ground is not smooth. this noise is from rear. I assume this is caused by same failure.

Or take it pedders for the steering and suspension check. Im pretty sure if you took it to the tire place and get them to look at it. Im sure when you explain it to them they will know whats wrong with it. Better then going back an forward on a forum arriving and no answer is it not.

sure, I will do it when next maintenance.

  • 2 weeks later...
  • 2 weeks later...
  • 4 weeks later...

all sorted after changed 4 new tyres and tailshaft balance.

first I did tailshaft balance but my car still got vibration problem

then I went to MRC and they said my tyres are worn uneven. the vibration problem is gone after changed 4 new tyres

thanks all your help, mates.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • I'm with you here. It's either loom has an issue, OR, injectors are not functioning properly. It could even be they're just constantly dribbling, hence the wet, but not firing.
    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
×
×
  • Create New...