Jump to content
SAU Community

Recommended Posts

spaz moment, the 235/40 compared to the 45, this will increase spedo reading yes?

i know only by likr 3-4% but i have a 10% speedo error (always reading to high) anyway

Edited by GH05T

The higher profile will make the car go faster than the speedo is reading, so if your speedo currently reads higher than you're actually doing, it will correct this somewhat...but rather negligible as you say.

Let's not use confusing terms that could be interpreted differently.

Speedo runs off the gearbox output shaft, so it takes its reading based solely on engine rpm and the gear selected, irrespective of what's happening at the tyres and diff. Therefore, 2000rpm in 5th will always make the speedo read the same speed (say ~80km/h) no matter what size tyres or diff ratio you have.

Increase your tyre diameter and the vehicle physically goes faster but the speedo reading stays the same. So if your speedo reads high, putting on larger tyres will make it more accurate. If it reads low, putting on larger tyres will make it more inaccurate.

Manufacturers usually calibrate the speedo to the standard tyre diameter and make it read a little bit high so that they aren't responsible for people's speeding fines.

  • 2 weeks later...
  • 2 weeks later...

received the tires, unfortunately i stuffed up the tire speed calculation (yep did it backwards in my head....derp).
my speedo error reads to high already, the new diameter for my wheels means it will now read higher again not lower so they really dont suit which sucks.

still unfitted
which sucks cos the tread pattern looks so nice

re listed in sa :P

http://www.sau.com.au/forums/index.php?app=forums&module=post&section=post&do=new_post&f=12


Edited by GH05T

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • UPDATE: Yes the GSP Axles are compatible. I installed it on my R34 today and they are working a treat! Turns out that the S13, S14, S15, and 200 SX all used the same axles as the HR34, and ER34 NA models. Which is 2 bolt x 3 pairs.  
    • Also build this EH ute with 370z motor and gearbox with a couple of turbos just for fun.  
    • Got the passenger door on plus the master cylinder and booster. Loaded up to take it home. At home, the colour changes a lot in the light.
    • Nothing cheap, but I have seen the AC Hydraulic DK13HLQ which is pretty close to what you're asking for. The problem is the hydraulic cylinder mandates that the back of the jack be a certain height and Skylines have fairly deep inset floor jack points. A more certain and cheap option is to get some nominal 2x10 inch lumber boards and have one board be 1.5 feet, the other board 3 feet. Glue it all together with lots of clamps to maintain pressure. Make two of these. The ramp suggested above is a good idea, it takes quite a bit of clutch slip to get over each of the boards. I only need the first ~1.5 inches for my low profile jack on a standard ride height car but a lowered car you want to go up to the full ~3-3.5 inches. Paint it or store indoors if you want it to last.
    • Ok. And Nistune? I read (here too) mainly on Stagea threads that it can by "turn off" with Nistune. But they say they still had the sensor plug in. Next week iam going to the Nistune(and other ECUs) tuner so i can finally make it work. I drove the car home and apart from the cut it drove great. No misfire no smoke no hesitation or rough start...so hoping it is this sensor that is missing  
×
×
  • Create New...