Jump to content
SAU Community

Help Needed R34 Gtr Immobilizer Problem.

lewks

By lewks,
in Car Audio & Electrical

 Share

Recommended Posts

lewks Newbie

lewks

Posted
  • Author
Posted

Do u have an aftermarket alarm ? who fitted it, do u have ignition lights, I had the same problem it was the idiot who installed the alarm had no idea how to.

Yes, there's a aftermarket alarm installed recently. Ignition light u referring to, is it the keyhole? how did u solve ur problem?

My situation is, last week battery gone flat. unplugged the +- and recharged it with a charger.

everything works fine as usual until on the same day i drove it to office n left it for few hours. after that i tried to start it, it can be cranked but unable to start. the throttle % isn't giving any respond on the screen when stepped on it.

and the immobilizer RED LED was ON. No solution and called for carrier and car being carried back home. After 2 days, it back to normal again. Then next day, it gone back to the same problem.

I gotta R34gtr v-spec Collaborator

I gotta R34gtr v-spec

Posted
Posted

http://www.sau.com.au/forums/topic/455132-alarm-install-warning/

Ignition lights are the lights that come on when u turn the key on, and go off when it starts.I had to have the alarm installed a second time but by someone who knew what they were doing.

lewks Newbie

lewks

Posted
  • Author
Posted

http://www.sau.com.au/forums/topic/455132-alarm-install-warning/

Ignition lights are the lights that come on when u turn the key on, and go off when it starts.I had to have the alarm installed a second time but by someone who knew what they were doing.

My ignition light isn't working, seems the alarm installer fked it up i guess? Btw, Thanks a lot for the info. anyway, my gtr mechanic told me to send it back to his workshop and he'll sort it out for me and not back to the installer instead.

  • Like 1

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      What accelerator cable can be used with greddy plenum

      By Duncan · Posted

      I was 99% sure the standard one is long enough to get there, you might just have to change the throttle orientation. If not, I remember someone having used an r31 cable instead, but that is probably harder to find than r33 by now...
    • V36
      What accelerator cable can be used with greddy plenum

      By V36 · Posted

      HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
×
×
  • Create New...