Jump to content
SAU Community

Recommended Posts

Just got my nismo side skirts in and I picked up new mounting hardware from nissan. I was hoping someone can give me some details about the mounting process, I assume all my lower mounting holes are present but what about the upper portion of the rear pieces?

Cheers

Link to comment
https://www.sau.com.au/forums/topic/455670-32-nismo-skirt-mounting/
Share on other sites

just uses double sided tape afaik

how much was the mounting hardware? what did it consist of?

would love to take mine apart clean and re fit

Just double sided tape won't do it. Maybe for the guard section, in front of the rear wheel. I mounted mine a few months ago. (3m tape). If you don't have the clips then sikaflex may be a option.

Best option is getting the clips and doing it properly.

Good info - slowridn73. They're a pain to track down part numbers etc

Use 3M PT1100 double sided tape. It's made for that kind of stuff. The Original side spats fits perfectly to the chassic, you wont get any problems with this tape.

Using it myself for two years now. Best tape for exterieur parts like side skirts or spats. But let it harden for a few hours after you applied it, best with a slight pressure against the spats.

  • Like 1

Double sided tape works best and its the way it's supposed to be done, don't f**k about with any type of glue you will regret it!

Double sided tape + clips. Water, dust and grime deteriorate the tape on the underside of the car. Plus it's super easy to line up with the clips.

  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
×
×
  • Create New...