Jump to content
SAU Community

Recommended Posts

Seat base might smell if it gets wet - and I persoanally don't want to be around.

*Edit - just noticed the typo - but I'll leave it there.

Nice morning this morning. :)

No smell at all. I just didn't want to allow it to get wet during the intense low pressure system over the past few days. PM me for bank details if you will. And I'll grab your address in the process. Regards Tez

I've been asked if I can reduce the price of the White GReddy Gracer side skirts for the R32. If I'm doing this for him, I'll do it for all. $380

I got the rear interior window trims back today. They look alright but Bryan cannot get rid of all the bubbling. Pics to follow tomorrow but I cannot in all honesty charge any more than what I paid for his labour which is $100

You'll understand why I'm only charging $100; but at least there's no cracking.

Trim-3_zpssnaoncs2.jpg

Trim-4_zpsgal4qcra.jpg

Trim-1_zpsfqnrubrw.jpg

Trim-2_zps2e8bc5rw.jpg

You'll notice there is a small patch over where the corner is most stretched.

The PO man told me last week that there'd be no problem bagging the seat base. But when it came time to post it, no Aust Post packaging would accommodate it. Had to scavenge a Nissan box quick smart. I do hope it was unmolested Frank. I would have preferred to bubble wrap it as well. Again, apologies.

A Lay-by has been placed on the GReddy Gracer side skirts.

Balance needs to be completed by 1st November.

Tomei sump baffle plate has been reserved too.

  • 1 month later...

GReddy Gracer Side Skirts

...are back up for sale.

Reduced to $350 due to forfeiture of a deposit.

I'll also throw in Rear Pods - unless they're not required.

Or, I'm willing to separate and sell the pods first for $90

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
    • Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...