Jump to content
SAU Community

Standard Boost Control On Rb20det

rayj

By rayj,
in Engines & Forced Induction

 Share

Recommended Posts

rayj Proficient

rayj

Posted
Posted

Hi

Just want to make 100% sure before I put my turbo on the car.

Is standard boost on a RB20DET with stock turbo simply controlled by the 10psi actuator, and a hose connected between the actuator and turbo?

Is there anything else, or is that it?

Another thing, the turbo currently on the RB20 is a VG30. This turbo will be swapped over to a stock RB20 turbo (in the next few days). The ECU is stock and has not been tuned for the VG30 turbo. In this situation is it okay to set timing at stock 15 degrees and drive the car carefully if I really need to use it until the VG30 is swapped out?

Thanks heaps :)

Link to comment
https://www.sau.com.au/forums/topic/456178-standard-boost-control-on-rb20det/
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      Ok, just the way you wrote it made it look like you had the stagger the wrong way around 
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I was getting anxious with the DVLA not knowing if the paperwork is fine or not, so I rang them. No update had been given, but I  was reassured that providing the box was ticked on the V750 then the application will go through fine. I've been checking the DVLA website pretty much every day, in the hope that it would have been done. Fast forward to Monday 29th  and I was greeted with a new screen on the check, and it finally showed as Taxed and MOT'd, woohoo! The car was in desperate need of a clean, not knowing when this day was coming it was put off. As far as I was concerned I had another 3 weeks  I'm not normally one for using snow foam, but I wanted to give it another try It hasn't cleaned up too bad considering it's 21 years old and lived on a boat for a number of weeks. The personalised number plate is J2 XBK, an illegally spaced number plate would have it read J2X BK. BK could either represent  the colour black or Baker, which is my surname. I filmed the first drive, the Youtube link will be at the end. I used the same driving route I did with the 323F V6 when I had a new exhaust installed, heres a couple of photos A few more since then Youtube video can be viewed here: https://www.youtube.com/watch?v=TjkFHPzjGDw
    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
    • Adam_ECR33
      Hello sau 👋

      By Adam_ECR33 · Posted

      Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
×
×
  • Create New...