Jump to content
SAU Community

Recommended Posts


Out of interest where would you put the auto flex? Assuming you're doing it yourself not looking at pics or posts? Before or after the cat? Would be keen to see all the pics of your build? Must be a insane machine? A veritable titan?


I have photos that show all of the exhaust except the front pipe where the flex joint was.
1 hour ago, TiTAN said:

IMG_1442.JPG

IMG_1443.JPG

IMG_1444.JPG

IMG_1445.JPG

IMG_1446.JPG

She wasn't pretty. But she got the job done.

4" dump, 3.5" front with flex pipe, 3.5" cat with 5" body, 3.5" to the middle muffler, 3.75" to the rear muffler and a 4" tip.

25/30 with a gt3582, 394kw @ 26 psi and 90db @ 3500.

This is the exact setup im going for.... ? atleast i know what to expect ?

2 minutes ago, TiTAN said:

 


Expect that the 38mm height difference in the block is far more annoying than you think it's going to be.

 

I have a grinder, hammer, welder and a soldering iron. We can make 38mm work lol


Stirred in natural yoghurt before serving:-) yum

Jack wanted to make a Korma chicken curry today? I'll show you how mate marinate the chicken. Set it aside. Get the oil hot close to bubbling then ad the spices stir and only just spoon in a few pieces! All the chicken dropped out the bowl into the piping hot oil an whalla!DSC_0149.JPGDSC_0148.JPG

Jack wanted to make a Korma chicken curry today? I'll show you how mate marinate the chicken. Set it aside. Get the oil hot close to bubbling then ad the spices stir and only just spoon in a few pieces! All the chicken dropped out the bowl into the piping hot oil an whalla!DSC_0149.JPG.1e949b087f3dda053e6ca7f4cdb3b4f0.JPGDSC_0148.JPG.68d26367b6202780e3b0c0dde2c346c1.JPG

This is my hand, splashed the piping hot oil onto it. Chicken Korma with blistering skin! Yum!
IMG_1442.thumb.JPG.0fce9583cf5f5bcf8b4935ef506b66f9.JPG

IMG_1443.thumb.JPG.d0de2311e426a5cd3ed835f560d9ce1f.JPG

IMG_1444.thumb.JPG.705ef0f2abdbf707daa9f61af518dd20.JPG

IMG_1445.thumb.JPG.d1d0421c0761cf69f4f7ad170d3388ec.JPG

IMG_1446.thumb.JPG.e4cb22dfeb9abb6e88f0bc62e10429a6.JPG

She wasn't pretty. But she got the job done.

4" dump, 3.5" front with flex pipe, 3.5" cat with 5" body, 3.5" to the middle muffler, 3.75" to the rear muffler and a 4" tip.

25/30 with a gt3582, 394kw @ 26 psi and 90db @ 3500.

Frankensteins monster, bolt of lightning to fire up that nasty s.o.b.!
I have a grinder, hammer, welder and a soldering iron. We can make 38mm work lol


Exhaust won't fit, intercooler piping won't fit, clearance to the clutch master cylinder is quite tight, cam belt covers need to be modded.

Wiring isnt an issue from memory, it's just anything that used to bolt onto the head or between the head and block are now 38mm too low/short/out of place.
6 hours ago, TiTAN said:

 


Exhaust won't fit, intercooler piping won't fit, clearance to the clutch master cylinder is quite tight, cam belt covers need to be modded.

Wiring isnt an issue from memory, it's just anything that used to bolt onto the head or between the head and block are now 38mm too low/short/out of place.

 

Sounds like a giant ill fitting jigsaw. Im sure il gwt it worked out with a lot of swearing and cursing


Jack wanted to make a Korma chicken curry today? I'll show you how mate marinate the chicken. Set it aside. Get the oil hot close to bubbling then ad the spices stir and only just spoon in a few pieces! All the chicken dropped out the bowl into the piping hot oil an whalla!DSC_0149.JPG.1e949b087f3dda053e6ca7f4cdb3b4f0.JPGDSC_0148.JPG.68d26367b6202780e3b0c0dde2c346c1.JPG


OUCH

Blistered up yet?


OUCH

Blistered up yet?

Amazingly looks pretty good today. Did 1 hour of cold water on off till the heat disappeared. Wrapped in sterile cloth and glad wrap. Nurse said just put antiseptic on for 5 minutes then pat clean keep re laying dressing.



  • Similar Content

  • Latest Posts

    • Don't even try to run it on the stock ECU if you're going to have the boost controller bring boost above ~10 psi. I've already told you that. If you use the Nistune ECU, you will need to CAREFULLY read the available documentation for Neo tuning, and read some threads on the Nistune forums, to discover the various things you have to do to prevent the ECU from going bananas when the boost is too high. The is a table associated with th boost sensor that must be modified to prevent it from shitting the bed. This is just one of the things that you will need to do to the tune in Nistune, because the Neo turbo ECU will be expecting to see a number of things (such as the TCS) that are not there, and you have to block the DTCs on those. It is totally not surprising to me that you are having the problems that you are, but the solutions to these problems have been known for >15 years. So just get it done.
    • Hi. Sry iam not a mechanic and iam not at the car atm so i dont know 100% but they told they measure those and even try to change those. AFM they have two. Coils are new a they have my old one too. Plugs too. ECU...we have 25 NEO stock and Nistune 25 NEO.   But i dont know if any one those could be the problem and why/if/what can cause this, Only thing they did not check is fuel...but that walbro 255 is new(like 1,5 years)... That fuel pressure gauge idk...but i let them know Any suggestions?   EDIT: how can they know if it is like you say he ECU pull power when it reaches a specific boost level that is too high? Tha car has boost controler
    • Can you clarify what you mean by boost cut, do you mean it misfires both when under load (driving) and when stationary and out of gear? Or does the ECU pull power when it reaches a specific boost level that is too high (boost control issue)? Does it occur at idle with no throttle? When you say "the ECU is OK", what ECU is it and why do you think it is OK? Have you used the NEO ECU, and if so do you have a MAP sensor attached? Same for the AFM, why do you think it is OK? Do you have any way to put a fuel pressure gauge on it (even just a mechanical one between the fuel filter and fuel rail)?
    • Hi.. Just another problem. So maybe you can help. I(my mechanic) done swap from my RB20DE NEO to RB25DET NEO. Everything is OK but we have a boost cut. Coils/Plugs are ok...AFM is ok. ECU is ok. I have Walbro 255 but it "changed" sound few months ago(you can hear it ouside) you did not hear that when it was new(maybe faulty?) Sooo...what now? What can cause this boost cut? It is even when you standing still...
×
×
  • Create New...