Jump to content
SAU Community

Recommended Posts

There isnt a whole lot of info on rb30dets in my desired relms of use. Most rb30dets area drag monsters...

Hmm suppose it's the difference between a punchy quicker less laggy spool or a wait for a bit and get the the the holly f##k on it scary spool. Response vs shear power balance. Loads of rb's you see with bigger turbo's tend not to be able to get off the line or blow up boxes half shafts and diffs. I'd say with the bigger turbo you would need a mental clutch and longer ratio to get the power happening or it would just snap stuff and light up the tyres permanently. Which is also fun:-)
6 minutes ago, TiTAN said:

 


High flows have been tried on an rb30 years ago. It was a cheap build basically stock Na bottom end with the 25 head and it came on like a light switch but come 5000 it hit a wall, by 5500 it had dropped about 100kw from memory.

 

This is no gd... mine will be a forged bottem end so looking to lean on it some ?


Hmm suppose it's the difference between a punchy quicker less laggy spool or a wait for a bit and get the the the holly f##k on it scary spool. Response vs shear power balance. Loads of rb's you see with bigger turbo's tend not to be able to get off the line or blow up boxes half shafts and diffs. I'd say with the bigger turbo you would need a mental clutch and longer ratio to get the power happening or it would just snap stuff and light up the tyres permanently. Which is also fun:-)

Being a 3ltr it will have more torque anyhow so perhaps response is the way to go? Don't forget I'm only a sheet metal worker who has never blown up a Cleavo Windsor c4 top loader or 9".[emoji4]
Gtx3582r with an 50mm external gate is what i was also thinking. Either way i think external gates gonna be better


I had a pre gtx series 35r with 0.82 rear. If you tweaked the waste gate setup you could have 20psi at 3500. Traction was non existent below 100km/h, for Street use it was too laggy to be quick and too fast to be usable without potential jail time. You would start seeing positive boost (a few psi) at 2500 with a bit of load.

Guilt-toy had a similar setup and should be documented fairly well on sau.

This is my dyno sheet, 26 psi and the dip at 145 was spark breaking down, done on a 33c day.

IMG_1502280990.305269.jpg
13 minutes ago, Beyond Blue R33 said:


Being a 3ltr it will have more torque anyhow so perhaps response is the way to go? Don't forget I'm only a sheet metal worker who has never blown up a Cleavo Windsor c4 top loader or 9".emoji4.png

I hear u can get cheap pipe? Gonna need some mikd steel and aluminium to make some pipe work. Proberly not till later in the year tho

  • Like 1
9 minutes ago, TiTAN said:

 


I had a pre gtx series 35r with 0.82 rear. If you tweaked the waste gate setup you could have 20psi at 3500. Traction was non existent below 100km/h, for Street use it was too laggy to be quick and too fast to be usable without potential jail time. You would start seeing positive boost (a few psi) at 2500 with a bit of load.

Guilt-toy had a similar setup and should be documented fairly well on sau.

This is my dyno sheet, 26 psi and the dip at 145 was spark breaking down, done on a 33c day.

IMG_1502280990.305269.jpg

 

Hell yeah, that looks right up my street. I wont be using it much on the street, mabe once a week at this stage. Il proberly get hooked at drive it all tje time lol

thats a run out at an airport, i am not even an amateur film maker obviously as its hard to even read any of the gauges. had spark breaking down at 160 then it clears up and keeps going, trapped at 242km/h at the 800m mark.

  • Like 1
6 minutes ago, TiTAN said:

thats a run out at an airport, i am not even an amateur film maker obviously as its hard to even read any of the gauges. had spark breaking down at 160 then it clears up and keeps going, trapped at 242km/h at the 800m mark.

Sounds gd ?

16 minutes ago, TiTAN said:

That's mainly to give you an idea just how quickly 400kw puts on speed.

If it's going to be a track toy, you are going to need some serious brakes to deal with stopping it. Upgraded pads and rotors won't cut it.

350 all round. Alpha omega brembo upgrade. Dba discs and bendix pabs. With all my cars its always been suspension, tyres, brakes then power.


Posted some pics of the boot fit out. What do you think of it?

Looks good mate, should sound good too.

A lot of bass is lost through the back seat of our skylines due to the steel plate etc but will still be plenty of punch no doubt.

Is it all hooked up and running now?
  • Like 1



  • Similar Content

  • Latest Posts

    • When you pulled it off, there is no signs of blown head gasket? Is it possible you have some other issues going on? Possible cracked blocked? Or do you think it's straight up lifting the head? Did you check what the head was torqued to before pulling it down (To see if possibly they're stretching, or starting to break threads out etc)?
    • Seems like a decent result for a modded JZX110. They are bulky in comparison to the 100 and 90 models (which I'd prefer myself) but they are getting very few and far between here in JP these days. Thanks for the detailed review and the import process into the UK. I also have a car which I'm hoping to export from Japan at some stage so it's good to know if someone from the UK was interested in it. By the way the corrosion underneath is par for the course for cars which were located in/near the mountains or along the Japan sea coastline. They get huge amounts of snow every winter and the sodium chloride is used on the roads. Many cars have some kind of rubber like treatment underneath but they tend to limit it to the wheel arches underbody and fuel tank. Suspension arms and sub-frames will have similar corrosion to your JZX110 which is a common sight. See it all the time and car dealers here generally don't even mention it unless asked.
    • If the sound goes away when you clutch in, the 1.5/2 way diffs are just shit, and you are a normal person. The diff is likely "fine" but driving at anything under 30kmh is a violent horrible experience. It would be exaggerated with solid diff bushings and subframe bushings if you have those.
    • Trailer got new mudguards to accommodate the new wheels Lightweight ally Painted, stickered and done ✅ 👌  
×
×
  • Create New...