Jump to content
SAU Community

Recommended Posts

Pull the rail off and unplug the injectors without removing them from the rail and crank it, make sure it's not a bad o-ring.


Already done start of the year. Also had them cleaned. Tried winding Cas while spraying individually into a bottle and all spray pattern looked good. Replaced o-rings and refitted but still dilution.

Bought a wideband. Removed cold start enrichment and leaned out at cruise

Still dilution [emoji15]

Time to swap out injectors...
  • Like 1

What size injectors and fuel pump?

Blitzed spring onion, mushroom, white onion red onion and garlic. Caramelised and Reduced with red wine, browned lamb rump chunks, made custom gravy 2 1/2 hours in slow cooker. Fresh sesame seed crunch bakery rolls and creamy garlic mash on the side. Full dilution :-) deliciousness!
  • Like 1

Blitzed spring onion, mushroom, white onion red onion and garlic. Caramelised and Reduced with red wine, browned lamb rump chunks, made custom gravy 2 1/2 hours in slow cooker. Fresh sesame seed crunch bakery rolls and creamy garlic mash on the side. Full dilution :-) deliciousness!

Tasted like insane beef Wellington in a roll.

 

2 hours ago, t_revz said:

 


Already done start of the year. Also had them cleaned. Tried winding Cas while spraying individually into a bottle and all spray pattern looked good. Replaced o-rings and refitted but still dilution.

Bought a wideband. Removed cold start enrichment and leaned out at cruise

Still dilution emoji15.png

Time to swap out injectors...

 

Aids?

  • Like 1


My missus made some tasty pulled pork rolls earlier in the week

Was dinner,breakfast, lunch and dinner [emoji4]

Yummo. 4 porks in 24hrs. My back couldn't handle it. Bummer about the unburned fuel past the rings. Would say maybe too rich or too aggressive timing. Too much duration on cams? Poor spray pattern etc. Worst case scenario hone or rebore. Compression test? Only a few thoughts. You know from a sheety. Have you tried pop rivets, tig welding or nuts and bolts. That's where my experience runs out so only a thought. it's just a thought. If my life is for rent.and I don't learn to buy. Do I deserve nothing more than I get. For nothing I have is truly mine. (Dido)
 
Aids?

Anything to do with beef pork or lamb and you're in:-) I've been recording the secret meat eats guy off sbs. Just smashed his beef Wellington recipe into the slow cooker with some modifications!
  • Like 1

Bummer about the unburned fuel past the rings. Would say maybe too rich or too aggressive timing. Too much duration on cams? Poor spray pattern etc. Worst case scenario hone or rebore. Compression test?


New engine

Def not running rich

Cams are mild

One of the injectors is ticking so most likely that's the culprit but I don't wanna upgrade to top feeds unless I'm sure.
  • Like 1

Yummo. 4 porks in 24hrs. My back couldn't handle it. Bummer about the unburned fuel past the rings. Would say maybe too rich or too aggressive timing. Too much duration on cams? Poor spray pattern etc. Worst case scenario hone or rebore. Compression test? Only a few thoughts. You know from a sheety. Have you tried pop rivets, tig welding or nuts and bolts. That's where my experience runs out so only a thought. it's just a thought. If my life is for rent.and I don't learn to buy. Do I deserve nothing more than I get. For nothing I have is truly mine. (Dido)

I'm having issues with the sthil fs38 idle at the moment then bogs down under power so??? Tuning a Nissan??? Apparently I can't tune a 2 stroke whipper-snipper properly.



  • Similar Content

  • Latest Posts

    • A 1.5 way is a 2 way. It is just a 2 way with a less aggressive ramp on overrun.
    • The ABS and/or TCS being missing/broken will not cause the engine to misbehave. It just casues CEL to come on and annoy you. The CEL is useless if it is always on, so you have to do the things you have to do to get rid of it, so it can be useful. Being a Stag ECU, then yes, it will not expect TCS to be present. But it will expect ABS to be present and working. You will need to either make the ABS CU talk to the ECU (don't ask me what that will take on an NA R34), and make sure the hardware is working....or, you just need to blank it out in Nistune. Do not persist with the stock ECU. You will just have problems. Gte it Nistuned. Start from there. DO YOU HAVE A BOOST SENSOR? The ECU's boost sensor that it. It is connected to the loom at the rear of the coil cover. Usually rides on the firewall on an R34, but is usually bolted down to a bracket along with all the other crap at the back of the coil cover when a Neo is dropped into another car. If you do not have it, the ECU will shit the bed. So, do you have one?
    • So sadly the fuel pump etc was not it. The pump and filter is new and it is still cutting around 4000 rpm. A read something about ABS/TCS (engine is from stagea and ECU too so no TCS) and i dont know for 100% that my car has ABS. It has ABS "cube" in engine bay but i dont think it works(or at least from my braking experience). Can be something like that?  I will be driving the car next week to Nistune tuner to properly see what is wrong...  
    • the Tomei LSD fluid with lsd kit. frustrated that it was shaking the car to crap and affecting everything else negatively, I pulled the diff last night, and removed the lsd carrier, could not find anything wrong, however it seem to be 100 locked up acceleration, and deacceleration, wondering if they sent me a 2 way not a 1.5??  either way I installed the stock open carrier back in place. test drove everything smooth as butter again. no shake, shutter, random, what felt like clutch slip and grab or drive shaft play, etc. something differently wrong in side the lsd. I might bother taking it apart (if possible) to figure out what's going on inside this carrier, as bought too long ago to return.  only draw back is its back to a one wheel wonder.
×
×
  • Create New...