Jump to content
SAU Community

DR30 bits needed

Doctor 30
 Share

Recommended Posts

Doctor 30 Community Regular

Doctor 30

Posted
Posted

I need the window rubbers where the Bpillar would be if it had one. If you have a dr30 you will know the ones I am talking about.

I need my drive shafts recoed or replaced but the R200 diff apparently hs different splines.

My LSD doesn't limit any slip anymore, It would be nice to know who in melbourne can tighten it up.

I am an extreme tight a s s so Please don't suggest that I fly over to japan to get them.

BTW, Any suggestions for getting cold air under the bonet?

Link to comment
https://www.sau.com.au/forums/topic/45765-dr30-bits-needed/
Share on other sites
rsx84 Veteran

rsx84

Posted
Posted

i had to replace my passenger or drivers side???forgot which one 1/4 window seals and had to get them from NZ, i did get both sides though are you after both as i can get you one side? the only luck i had at getting any here was from jaustech in SA but they will only sell the whole window and seal and i'll only tell you the price if you want to ask!! pm me if you want the seal i have.

Link to comment
https://www.sau.com.au/forums/topic/45765-dr30-bits-needed/#findComment-932108
Share on other sites
NeoLokie Enthusiast

NeoLokie

Posted
Posted
I need the window rubbers where the Bpillar would be if it had one.  If you have a dr30 you will know the ones I am talking about. ..*snip*..

Window rubbers are about $20 each from any nissan dealer, you just have to supply model/chassis numbers and be prepared for plebs who don't know what a dr30 is.

Link to comment
https://www.sau.com.au/forums/topic/45765-dr30-bits-needed/#findComment-941973
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Black_CSR
      Wheel Sizes & Offsets For Skylines

      By Black_CSR · Posted

      ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..    If i get this - will this fit all around: Size: 18 x 8.5 +37 - n what tyres size tyre should i get for front n back?  
    • GoHashiriya
      From Japan and back to Europe, my sh*tbox R34 GTT

      By GoHashiriya · Posted

      Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Kinkstaah
      WTB R34 GTR Guard Liners

      By Kinkstaah · Posted

      Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • itsmeyo
      WTB R34 GTR Guard Liners

      By itsmeyo · Posted

      Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • The Bogan
      NC MX5

      By The Bogan · Posted

      I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...