Jump to content
SAU Community

Recommended Posts

Just went to install my pump on the weekend and I popped off the lid. I havent drained the tank yet but the pump looks far down, Im not even sure Ill be able to change it. [This is while having myself squashed in the trunk to take a peek lol] Took a look under the car and to drop the tank it almost looks as if you will need to drop the sub frame.

What does everybody do here? Im going to try draining the tank and sticking my arm in but it looks like itll be a pain in the arse. Thanks guys!

Link to comment
https://www.sau.com.au/forums/topic/458211-r34-4-door-fuel-pump-install/
Share on other sites

You have to do it through the lid.

It's entirely possible. Just reach on in.

To drop the tank you absolutely do need to drop the subframe... aaand in any case, you still have to go in through the lid.

Source: Changed the pump in my car approximately seven million times.

  • 2 weeks later...

So to pull the pump, its held on a bracket [see pic] that slides upwards, this is on the front inside. Size difference is obvious lol

Put in a Nismo R34 GTR pump as the GTT version doesnt flow enough for what I need. It is a tight fit and some modification is required. Ended up:

Trimming the feed line above the pump just below the upper notch as the pump is way taller.

Cut the size of the sock tube to put it roughly in the same place as the OEM pump sock.

Trimmed a bit of the bottom of the bracket [sock wont line up to bottom slot due to pump being wider]

Worm clamped it to the side of the bracket.

Trimmed one of the insulation tabs due to it pressing against the tank.

At this point Im hoping it doesnt make too much noise being against the tank, but only time will tell. :blink:

The good news is the connector fits right into the lid so no need to swap connectors, left the smaller ground alone as I have previously read it is not req for install. I have the tomei pump relay harness which will be installed soon to skip the modulator. Didnt know that some R34 GTR's have the battery in the trunk so I will be running a wire after the fuse to the back of the car and grounding the negative.

post-133882-0-12483200-1437663940_thumb.jpg

Edited by tommytomatoes

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yup. You can get creative and make a sort of "bracket" with cable ties. Put 2 around the sender with a third passing underneath them strapped down against the sender. Then that third one is able to be passed through some hole at right angles to the orientation of the sender. Or some variation on the theme. Yes.... ummm, with caveats? I mean, the sender is BSP and you would likely have AN stuff on the hose, so yes, there would be the adapter you mention. But the block end will either be 1/8 NPT if that thread is still OK in there, or you can drill and tap it out to 1/4 BSP or NPT and use appropriate adapter there. As it stands, your mention of 1/8 BSPT male seems... wrong for the 1/8 NPT female it has to go into. The hose will be better, because even with the bush, the mass of the sender will be "hanging" off a hard threaded connection and will add some stress/strain to that. It might fail in the future. The hose eliminates almost all such risk - but adds in several more threaded connections to leak from! It really should be tapered, but it looks very long in that photo with no taper visible. If you have it in hand you should be able to see if it tapered or not. There technically is no possibility of a mechanical seal with a parallel male in a parallel female, so it is hard to believe that it is parallel male, but weirder things have happened. Maybe it's meant to seat on some surface when screwed in on the original installation? Anyway, at that thread size, parallel in parallel, with tape and goop, will seal just fine.
    • How do you propose I cable tie this: To something securely? Is it really just a case of finding a couple of holes and ziptying it there so it never goes flying or starts dangling around, more or less? Then run a 1/8 BSP Female to [hose adapter of choice?/AN?] and then the opposing fitting at the bush-into-oil-block end? being the hose-into-realistically likely a 1/8 BSPT male) Is this going to provide any real benefit over using a stainless/steel 1/4 to 1/8 BSPT reducing bush? I am making the assumption the OEM sender is BSPT not BSPP/BSP
    • I fashioned a ramp out of a couple of pieces of 140x35 lumber, to get the bumper up slightly, and then one of these is what I use
    • I wouldn't worry about dissimilar metal corrosion, should you just buy/make a steel replacement. There will be thread tape and sealant compound between the metals. The few little spots where they touch each other will be deep inside the joint, unable to get wet. And the alloy block is much much larger than a small steel fitting, so there is plenty of "sacrificial" capacity there. Any bush you put in there will be dissimilar anyway. Either steel or brass. Maybe stainless. All of them are different to the other parts in the chain. But what I said above still applies.
    • You are all good then, I didn't realise the port was in a part you can (have!) remove. Just pull the broken part out, clean it and the threads should be fine. Yes, the whole point about remote mounting is it takes almost all of the vibration out via the flexible hose. You just need a convenient chassis point and a cable tie or 3.
×
×
  • Create New...