Jump to content
SAU Community

Recommended Posts

Looks like I managed to create a discoloured hard patch of leather after having an accident with the contents of a DampRid moisture absorber while the car was in the garage for a few months. Needless to say, I'm pissed off with myself and even a few hours soak of my Meguiars leather cleaner/conditioner hasn't done much to restore it to any degree.

So I figure it's probably best to just replace it. Thankfully the backrest is unaffected. Anyone got a black one in excellent condition (as mine once was until now) they'd like to sell? :/

Many thanks mate. Hopefully this one can be saved because DampRid, like most moisture absorbers, is a caustic soda, from what I understand. :/

Still, I'll give him a shot before I call Raj at Steve Jarvin for a replacement seat. It's much appreciated!

Looks like I'm calling Raj. It's too far gone. Let that be a warning to anyone else who uses moisture absorbers, like DampRid, etc. I'm keeping it on the floor like I used to. At least I can easily replace floor mats. :/

  • 1 year later...

Apologies for resurrecting this thread but for the sake of relevance, I'm sticking to it!

So it turns out Nissan in Melbourne finally got back to my contact and advised that a complete rear bottom seat assembly is no longer in production. I'm having a very hard time believing that for a seven year old vehicle, personally. I'm thinking of going through Amayama and see if they have better luck than I do. Anyone have any experiences with Amayama they'd like to share with me before I go forking out close to $2k for a seat?

I have used Amayama plenty of times without issue, but not for anything that large, postage is going to be a killer.  If they have stock in UAE, it is usually considerably cheaper for the item, but postage will be considerably more than Japan.

Have you tried an auto upholsterer?  it will likely be cheaper to have it re-upholstered than replacing it.

It will be marginally cheaper, however, the problem may possibly be that the caustic Damp Rid may still be lurking in the foam padding and if it is, it'll just destroy that leather trim as well.

I'm thinking of checking out some local wreckers for any reasonably pristine candidates but failing that, I'll be looking for something new, albeit with the massive expense in shipping the damn thing. :/

  • 2 weeks later...

Looks like after busting balls a little more, Nissan Australia (Melbourne) got back to my guy at Steve Jarvin and they do have a trim assembly, which is basically the seat without the frame. It's just a matter of unclipping the old seat from the existing frame and clipping the new one on in its place. Hopefully they're right because it's a $1080 mistake if they get it wrong for me.

Still, I'm pretty chuffed to hear about that and I can finally restore Max Jr back to normal. Let's see what happens when it finally arrives in a few months (sea freight).

  • 4 months later...

Looks like Nissan Australia got it wrong and sent what was only the leather trim but not the cushion as well. Steve Jarvin's boys (sadly, Raj is no longer there, so there goes any reliability from those guys too) are supposedly being told by Nissan (Melbourne) that now even that trim is no longer stocked in Japan. I suppose after eight years, they can only carry so many spares but the parts are dwindling fast for these vehicles.

So my options are two:

  1. Seek out a wrecker in Sydney with a suitable seat
  2. Try out Amayama

I've lodged an order with Amayama to see what they come back with for the entire seat assembly, at almost double the cost of what this trim order was, which thankfully I'm not paying for. Anyone dealt with them before? Anything you can share about your experiences or what you've heard would be nice.

Otherwise, anyone know of a decent wrecker in Sydney for Nissans/Infinitis? At this rate, I don't care if it's not the exact same design as long as the colour is still black. I've been out of the spares game for a while when it comes to wreckers, so I'm open to all suggestions.

  • 3 weeks later...

Final entry in this saga. Even Amayama can't score one. I realise the car is eight years old but I expected a little more support than that. According to Nissan Australia (Melbourne), even the Infiniti seats won't fit because there's a difference in the floorpan where the seats clip into, etc. Smells of bullshit to me but there you have it.

So I'm getting my mate to pick up the $1000 leather trim that he was able to obtain, thankfully, and I'll find an upholsterer who can fit it up for me when I get back from my work overseas. With a bit of luck, maybe the existing foam will be salvageable in that either the caustic liquid never made it past the leather and into the foam, or otherwise the foam can be cleaned up reasonably well to avoid a recurrence.

Valuable lesson learned.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • The car/ECU will have all the sensor that it needs and expect to have. I think i do not have to explain to you how the Link is way better specialy if you have swapped engine   I just do not want to deal with any "problems" cuz i have only Nistune which i learned is not that great and in my case cant even deal with that speed problem (Link can) And of course it will be way more easier to tune and diagnose and safe. And for the ECU/speed problem...i dont know.
    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
×
×
  • Create New...