Jump to content
SAU Community

Recommended Posts

Hi guys,

Just had brake pads changed and disks machined on my 2007 370GT coupe, and soon I am starting to have the annoying squeal noise at low speed to full stop and reversing particularly. Do you all have the squeal noise? What brake pads would you recommend for good performance and quietness?

Any advice is much appreciated.

Cheers

Leon

Link to comment
https://www.sau.com.au/forums/topic/459406-370gt-brake-pads/
Share on other sites

Sorry about the stupid question, how do you know the dust? Can you see it from the disk? Mine is brand new Akebono pads ( not bad reviews), not sure if it is the dust that causes the squeal noise. Normally in the morning it is the worst when reversing, as it goes and warm up, still has the noise but gets better.

Some pads make squealing noises. Usually those pads are high performance and have a usable range which is higher and that's why in the morning you hear it the most. You should get pads which are usable from low heat range to high where possible. All depends how you drive as well. I drive like an asshole so my brakes are usually always pretty hot.

Yep, what Colin said. As for how do you know the dust, I'm guessing you mean how do you know how much dust the pads are producing. It's pretty simple really. Just look at how dirty your rims get a few weeks after cleaning them. If there's not much dust, then they don't produce much dust. ;)

  • 1 month later...

I use DBA 4000 series slotted discs and EBC red stuff brake pads. Excellent performance for the wild driver (me) and no squeal.

Max, I have decided to go EBC red stuff! After two months it is still making the noise when cold, time to change. I don't want to change the full set yet as only the rear are having the noise. My front Akebono pads are only two months old. Is it ok to just replace the rear with EBC red stuff?

Thanks for your input.

post-77895-14443806589269_thumb.jpg

If it's only when cold, chances are you might still cop it with the EBC brakes too. I bought them for their stopping power and minimal dust under abuse. So far, I've been fortunate to go squeal-free but on a cold morning just rolling out of the garage, they do give a little vibration until they've warmed up after a couple stops.

If you still decide to go ahead with them, no harm in just replacing one end for the moment. It'll feel better than what you already have but once you do the fronts, where most of the braking power is, you'll want to stop more than you speed. :P

...not really. ;)

Oh no.. was having all my hope on this.. Guess it is common for the performance pads. My Akebono pads are the same and it still stop after few hard foot. I will do more research then. Are your slotted disks better than the original for heat? I also remember you have said your Megan racing muffler sounds amazing in another thread. It is on my list as well. I am following you.. haha.. Thanks for your help Max!!

Oh no.. was having all my hope on this.. Guess it is common for the performance pads. My Akebono pads are the same and it still stop after few hard foot. I will do more research then. Are your slotted disks better than the original for heat? I also remember you have said your Megan racing muffler sounds amazing in another thread. It is on my list as well. I am following you.. haha.. Thanks for your help Max!!

It isn't a definite thing with performance pads but it is certainly possible. Like I said, I've gone squeal-free with mine, even when cold, but others have had the slight cold squeal. Unless it's happening every time to apply the brakes across the entire temperature range, it's hardly annoying enough to be an issue for me. As another example, I use Bendix Ultimate pad on my shitbox Ford wagon with DBA4000 series discs. I get zero squeal out of them. However, a friend did the same to his XR6 ute and he gets a squeal at low speed. He breaks balls about it because mine doesn't do it but he doesn't seem to understand that it's just luck of the draw.

Slotted discs are beneficial for removing dust that normally gets trapped between the pad and the disc, giving your pads better bite. I don't know if they do anything for temperature so much because on my roughest days, I've managed to warp a set of DBA4000 slotted after around 12,000km on my Maxima back in the day.

If you want to keep the temperature down, you use cross-drilled discs. HOWEVER, don't waste your money on cross-drilled. You're not driving a race car, smashing your brakes in from > 200km/h at bends every 200m. The holes inevitably develop fractures which is a sign to throw them out not long after. Slotted is the most you ever need to go in my opinion, even if you drive like a bastard like I do at times. It used to be all the time, which is why I managed to warp those discs so soon, but traffic these days is bad enough in Sydney such that there's nowhere to speed your bum off anyway.

As for the muffler, beauty is in the ear of the beholder. I like cars that sound tough but I can't drive them all day with that horrible drone in the cabin. The Megan Racing muffler gives the vehicle a nice note without being obnoxious. Others here have other preferences which you should check out too.

  • Like 1

Relax dude. We all share our experiences here. No difference. I'm not always this verbose, typically when someone doesn't bother searching through existing threads, much to their offence. Screw 'em.

Edited by The Max

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, i’m making a rb25det coil loom for Vag short coil. Can anybody tell me which Ecu signal wire belong to coil number 1 and 2,3,4,5,6? The connecting switch in above pic is 8 wire i think white is for +12v and black for earth.
    • Was there ever a model of the Stagea m35 that didnt have a badge on the grill? I thought I saw that somewhere, some aero edition or something? I cant find it again? davemoto
    • Its a 2002 vr-x four VQ25DET, silver. Coil overs, lowered, polished alloys and sport exhaust. Bit of a project, was sitting in a shed for a while but runs and drives great.
    • I wasn’t able to replicate the sound anymore. It was a one time sound so maybe it was just coincidence but it was like small pebbles being dropped in a coke can.   should I try cleaning the MAF? It could be it’s functioning but dirty? I don’t know.
    • Update 4: Hi all. The car drives again! Haven't driven for long, only to store it in the garage again, but the test drive was successful. The coolant and oil leaks seem to be fixed for now. Temps on the engine were also very good, while moving I never even saw 80C water during the approx. 30 minute drive. Ate up all the coolant in the reservoir though so will have to fill that even more when I go to the car next time. One thing that pisses me off is that the RPM gauge is still f**ked, I even resoldered the board twice and used copper paste on the silly screws that are used as connections. Next time I take it out I'll take apart the board and fit new components, I'll see if I can get a replacement IC for it.  I have an appointment set for 22nd of September for the engine tune to 370hp. Alignment also still needs to be done. My hope is that I can get all the legal stuff over with by the end of this season. Anyone of you have advice regarding intercoolers? Currently there is an APEXI core fitted, one of those weird hybrid ones, 600x270x76. I don't think it's bad but it's not new and now I still have the chance to change it now to legally include it in the paperwork. Only issue is that the only options that would arrive in time are a HKS Type R intercooler or generic Ebay spec intercoolers comparable to a JustJap one. Ideally I'd order a Plazmaman but it takes over a month to receive which would mean making the car legal has to wait until next season. Would love to hear some input on this. Same story for my injectors, the previous owner was a nunce and put ID 1050x on the engine. They work but are obviously not ideal at "normal" power levels. But I don't see a reason to change them unless the tuner says it's necessary. I read online before buying a different exhaust that the top secret style rear diffusers won't fit due to the size of the rear resonators. My buddy and I made it work by slightly "adjusting the shape" of the mounting bracket and making some spacers out of 3d print for the mounting bolts. Fits like a charm. Just putting this here in case someone has this problem. Even the hefty HKS Silent Hi Power rear can fits without hitting anything.
×
×
  • Create New...