Jump to content
SAU Community

My R33 Gt-r V-spec From Finland!

Taiquri
 Share

Recommended Posts

Taiquri Rookie

Taiquri

Posted
Posted

Hi! I started my project 2010 and now its almost finished. I have test drive done and mot done. It still need mapping and new paint job. It was almost stock when i bought it from UK. I wanted to share some pictures of making. I am aiming 800hp+ power. Still need lots to do. Some cleanin and wanted to sandblast + powder coat subframes etc.

Partlist:

New n1 024u block
Ported head
New n1 crankshaft
Tomei conrods
Tomei 264 procams in/ex
Tomei gaskets
Cp forged std size pistons
ACL Bearings
ARP bolts head/conrods/flywheel
HKS cambelt
HKS fuel rail
HKS cambelt
HKS mushroom air filter
Greddy intake manifold
Greddy oil pan extension
Greddy Front diff cover
Ati race damper
N1 oil pump
N1 Water pump
Custom boost pipes with wiggins clamps
Bosch motorsport fuel pumps x3
Bosch motorsport fuel pressure regulators x2
An8 braided fuel lines to fuel rail, an10 return
Injector dynamics id1000 injectors
r34 gtr coilpacks
Custom made radiator
Big intercooler (arc?)
Titanium downpipe 4"
Titanium Intake pipe 4"
Titanium exhaust 4"
Titanium fuel surge tank
Single turbo exhaust manifold, fireproof steel 310L

25042010184.jpg25042010190.jpg

Link to comment
https://www.sau.com.au/forums/topic/459484-my-r33-gt-r-v-spec-from-finland/
Share on other sites
Taiquri Rookie

Taiquri

Posted
  • Author
Posted

Making fuel system. Some pictures of last days. Will continue soon! We have long winter which takes many months, so propably will map&dyno it before it and take it to road on next year.

20150818_222753_zpsroxv71d0.jpg20150827_162203_zpswkz5ijzs.jpg20150827_162224_zpsrcr1tds9.jpg20150823_222413_zps7fhrvvgr.jpg20150808_170105_zps2czn6egk.jpg20150827_215742_zpswtp2br5j.jpg

  • Like 2
Taiquri Rookie

Taiquri

Posted
  • Author
Posted

I love this! Well done!

And :welcome:

Thank you! This is interesting forum. I Like to read projects and fabrication topics! This is my third skyline. I have read gtroc lots but it is slightly boring because companies build cars.

I have done all welding&modification&fabrication and engine building on car. Camhead is machined on engine shop. I actually start building engine 2008 to my old R32 GTR but decided to change to R33. Last year i did MOT & registration and drive 6000kms. I had oem twin turbos bolted (because Finnish law does not allow to change turbos) so i know engine works fine :)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Cas issue

      By joshuaho96 · Posted

      Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • joshuaho96
      Jacks that fit under GTR lips that can reach the subframe?

      By joshuaho96 · Posted

      On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Duncan
      Mistakes were made, my R34 Story

      By Duncan · Posted

      Nice....looking forward to that update
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      Neg, the top one is actually for the front. The sizes are 18x10.5 +18 and 18x11 +32.   I measured many times but I'm sure I'll have problems as this is the thread for problems.
×
×
  • Create New...