Jump to content
SAU Community

R32 Gts-t Bris

fsmout
 Share

Recommended Posts

fsmout Collaborator

fsmout

Posted
Posted

Hi,

I am selling my R32 Gts-t unfortunately......I have had it for 9 months now, i just a job at the G'Coast and in 4 months i have put 11,000Kms on the clock :-(

I have been doing it up from stoke and here are the spec's;

Km's: 99,000

Engine: RB20DET, Turbosmart BOV, PWR 600x270x70 tube and fin intercooler(1 month old!!)/ with stainless steel piping, K&N pod filter

Exhaust: 3 inch Mandrel Bent from Turbo back inc split dump and rear 4inch cannon - installed 2 months ago!!

Wheels: AWA 18's with 235/40's all round - Bought new 1 month ago!!90% tred

Build date: 10/1992

Imported: 2002

Colour: Full custom respray Silver/Green Ice Pearl - No rust or panel damage

Body: M-Spec Side skirts, clear side indicators, shaved rear wing

Service Hist:100k service just completed inc Timing Belt, Iridium Plugs, Motal 8100 full syn oil, water pump - i have changed the oil every 3-4000kms until the 100k service.

Suspension: Front coilovers and rear Beilsine & Kings, Front N1 strut Brace

and i also had new tint put on 2 weeks ago

Email me for some pics as they are to large to load up

i am sh&%&^*ed i have to sell it now but im going to lose way to much if i keep it :-( with the k's i will be racking up

It's in great condition and Dr Kustom has done an awesome job on the paint!!

~~~~~~~~~~$16,500~~~~~~~~~

You can contact me on 0404 077 220

or at [email protected]

Cheers

Francisco

Link to comment
https://www.sau.com.au/forums/topic/46061-r32-gts-t-bris/
Share on other sites
fsmout Collaborator

fsmout

Posted
  • Author
Posted

yeah it is the standard pump - the next upgrades to the car would be to upgrade the turbo, pump and boost it?? i think from looking arround at other dyno charts of cars with similar mods it should be at around 145rwkw+, but with those mods above you could expect anywhere from 190-220rwkw depending on engine management. I am just about to renew the rego for another 6 months - next week

cheers

Link to comment
https://www.sau.com.au/forums/topic/46061-r32-gts-t-bris/#findComment-936946
Share on other sites
MR R32 Experienced

MR R32

Posted
Posted

I was not asking for performance reasons. Apparently the fuel pump on the 32's are amongst the worst you can get.... When I changed it on my last 32 it was not cheap.

Can you please send me pics for this car asap. Please send to [email protected]

I am very interested but going overseas tomorrow for a week...

Link to comment
https://www.sau.com.au/forums/topic/46061-r32-gts-t-bris/#findComment-937188
Share on other sites
  • 2 weeks later...
  • 2 weeks later...
fsmout Collaborator

fsmout

Posted
  • Author
Posted

hi, more pic's - email me for hi res pic's

I will take $17,000 and i am prepared to move the price around if i include or remove the mags (-$1200) and/or intercooler(-$1000). They are like new so i can get good money for them and i still have to stoke items.

So $14,800 for the car with the stoke mags and intercooler.

thanks

Link to comment
https://www.sau.com.au/forums/topic/46061-r32-gts-t-bris/#findComment-965139
Share on other sites
  • 2 weeks later...
  • 2 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Gareth87
      What should I do next to hold the head on

      By Gareth87 · Posted

      I can see between the water jacket and cyl 3 there wasn't a hard line of combustion gas. It certainly appears that the issue is coming from there. Yes, checked the tension. All at 100ft lbs where I set them 5 years ago. These blocks can crack but generally when they have been over bored. Mine is only 0.5mm oversize at 89.5mm. They break between cylinders around the 91mm mark. No sign of that with mine. My gut feeling is the head gasket lifted a while back when the studs stretched and i bandaided it by retorquing the studs. It's finally let go.
    • TurboTapin
      new 1.5 LSD issues/concerns

      By TurboTapin · Posted

      My Nismo 1.5 churps a bit on reverse turns when cold, but besides that feels like a stock diff.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Yes, but, I paid cash and I'm pretty sure the receipt was in the bin 10 minutes after I got home Note to self, keep all receipts
    • MBS206
      NC MX5

      By MBS206 · Posted

      Bunnings would have just handed you your money back on that one!
    • The Bogan
      NC MX5

      By The Bogan · Posted

      So, version 4 intake is on its way I was looking at these a while ago but at around $200 or more it was a little pricey for something that might not work, but, I had it in my watch list, but, I got a message saying it was on special, and I had a code thingie to use, it eventually came in at $120 delivered, so BAM, BUY NOW.....LOL I'll need to have a look when it arrives but I feel it will "look" better than what I currently have, as it comes with a PCV fitting, so I will be able to get rid of the alloy pipe that goes to the throttle body with the PCV fitting  Well, that's what the voices in my head are telling me  Oh, and this happened today Yeap, it was a Trojan, and it was cheap, so I headed back to the hardware store and actually spent a little bit more on a heavy duty,  one that was actually recommended by a plumber mate, a Cyclone one with a fibreglass handle that is actually rated for clay The broken shovel will eventually be "modified" into a short handle shovel
×
×
  • Create New...