Jump to content
SAU Community

Recommended Posts

Just spoke to a friend of mine who had his 100,000 k service done today. He was lucky to have driven 15kms and his engine siezed.

He first noticed a loud clunking/ticking/rattle from the engine that he describes as a metal on metal sound. Now the engine will not even tick over.

The maintenance he had done was:

Timing belt changed

Tension pulley tightened (due to belts screaching on startup)

Several seals replaced (ie, crank seal)

fuel filter changed

oil / oil filter change

One thing that sounded a bit dodgy was a crank bolt which he ( the mechanic) apparently snapped and had to replace.

We are going to confront the mechanic tomorrow and want to make sure we know we know what is wrong first so the guy cant feed us any bulls%*t.

I think the most likely cause is the timing belt not fitted correctly.

What do u guys think and how can we confirm that this is the problem?

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/
Share on other sites

if your motor wont turn over means your engine is ****ED. happend to me on my 300zx, after it siezed up had to rebuild the motor. good luck and please dont be shy to confront the mechanic and make him pay for the rebuild.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936789
Share on other sites

Whatever happened clear case of mechanical screw up on their behalf. I don't quite know how they'd try and wrangle out of it.

but if they do try, get an independent inspection ASAP (like today) by another party or two, get it in writing.

And if you need to take legal action against the mechanic involved, this will help.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936965
Share on other sites

I'm thinking out loud here, but goig back about ~11 years ago I had a suzuki swift gti, going in for a timing belt/cam belt change. Apparantley the pulley needed to be put on a special way which the mechanic did not do.. we drove about 80k's, and when we tried to restart the car, it would not start... Thankfully it didn't blow the motor, but was an expensive tow from Bells Beach to Melbourne, ended up taking the matter to the Small Claims tribunal and won.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936968
Share on other sites

Yeah the oil was checked and even replaced after my friend told the mechanic the car is making a noise. The mechanic said just to put a thicker oil in it and it will be fine. Then 10 km later bye bye engine.

The car is getting towed to the mechanic now and the dick still thinks its the oil.

I dont think he has a clue.

Link to comment
https://www.sau.com.au/forums/topic/46083-engine-siezure/#findComment-936981
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...