Jump to content
SAU Community

Recommended Posts

So I just did the belts on the stagea and low and behold whilst flashing the light about I see some bare wires.

I'm assuming it's the knock sensor , it's a two wire plug between the v under the intake. Can be seen from the front in the opening between the heads. One wire is bare other looks to be cut. (Looks like mice got to it :-/)

Car does not ping.

So my question is. Does the intake have to go in order to get to it and fix the wiring ? If so should I just do the rocker cover gaskets(passenger side weeps only just) and plugs 143xxxkm. Or am I going beyond what's needed to get to the knock sensor.

Car goes beautifully just last weekend did 1000km round trip and got 720km out of a tank (ultimate ) with no hesitation what so ever even snapped the speedo on a overtake.

Thanks for any and all advice.

Edited by malialipali

Surprisingly common, I have had to repair a few. I should have a spare knock/injector loom here somewhere if you can't find something local.

Yes the lower plenum needs to come off to replace it.

Nice and warm Dale, for many hours. Smart little f*krs would just nest it out with rags and grass, anything they can find to make a cosy and protected home.

As soon as the door unlocked they would know to scurry away.

Surprisingly common, I have had to repair a few. I should have a spare knock/injector loom here somewhere if you can't find something local.

Yes the lower plenum needs to come off to replace it.

Is the wiring shielded? If not I can repair the plug thats not an issue. If it is shielded then yes I would need the part.

Is there a part # ? Same as the VQ35s? by any chance. Is this the guy I'm looking for https://www.z1motorsports.com/oxygen-and-knock-sensors/z1-motorsports/350z-g35-vq35de-knock-sensor-sub-harness-p-5833.html?osCsid=keol7gu21kictn9cop24pqrhb4

If I cant find anything by end of tomorrow, I'm happy to pay what it cost + express bag postage Scotty.

OK just did a quick google (currently at work so cant dedicate too much time) looks like 50ohm RG58U coax on the positive side. 99% confident I can repair it. So will give it a crack to repair the wire.

If the car ends up off the road for a few days so be it - ive got a spare.

Cheeky little feckers they are...

I was actually joking when I said looks like mice got to it o.O , now I find that this is actually true and common. WTH!

May as well dot the plugs since I'm gonna spend next Saturday over an engine bay.

Anything else I should to preventative wise. Not fussed on $ , I'm driving the car to Adelaide next month and need to make sure its healthy.

Thanks a bunch on the help All .

Edited by malialipali

You had better get it apart and see what's broken first, you may need the knock sensor too.

Yes, that loom looks similar, on ours it's wired into the injector harness, but you can simply run that one in addition to replace the chewed out part.

  • Like 1

So spent most of the day (38C here today) over the engine bay listening to tunes and drinking beer.

Stripped the intake off, rigged up a hose to my wet and dry vac and vacuumed up sand/ grit, dirt 2 snail shells ??????? (where the hell do they come from) from around the intake before taking it apart.

Cleaned the intake sections with carb cleaner . Got the harness out and assesed. Looked like shit!. stripped it back de-pinned the connector. Soldered in new leads. Coax wire was perfect fit. Soldered the pins and reassembled the connector.

Knock sensor tested at 562K Ohm (well within the range). With the harness it tested at 559K Ohm still in range.

Did the spark plugs at the same time, who ever did the car last should be slapped !!! had Champion Platinums in there with a 14 (NGK4) heat range .... way too hot , guess they whacked in 350 plugs, electrodes were worn to heck too probably 1.4-1.5mm gap. Got some LFR6AIX.

Put it all together and the moment of truth, fired up first go. Went for a test run , Significant improvement on take off, tried stalling it up and lit up the rears ! never happened before.

I think I just thought these cars were good at WOT and sluggish otherwise......... proven wrong now. Very very happy with the improvement.

Thank you all for your help , Esp Scotty for telling me the whole intake needs to come out.

Total cost $123.70 including the plugs (had to buy the coax and I ran out of heatshrink)

Edited by malialipali
  • Like 2

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Update 3: Hi all It's been a while. Quite a lot of things happened in the meantime, among other things the car is (almost) back together and ready to be started again. Things that I fixed or changed: Full turbo removal, fitting back the OEM turbo oil hardlines. Had to do quite a bit of research and parts shopping to get every last piece that I need and make it work with the GT2860 turbos, but it does work and is not hard to do. Proves that the previous owner(s) just did not want to. While I was there I set the preload for the wastegates to 0,9bar to hopefully make it easier for the tuner to hit the 370hp I need for the legal inspections that will follow later on. Boost can always go up if necessary. Fitted a AN10 line from the catch can to the intake hose to make the catchcan and hopefully the cam covers a slight vacuum to have less restrictive oil returns from the head and not have mud build up as harshly in the lines and catch can. Removed the entire front interior just shy of the dashboard itself to clean up some of the absolutely horrendous wiring, (hopefully) fix the bumpy tacho and put in LED bulbs while I was there. Also put in bulbs where there was none before, like the airbag one. I also used that chance to remove the LED rpm gauge on the steering column, which was also wired in absolute horror show fashion. Moved the 4in1 Prosport gauge from sitting in front of the OEM oil pressure gauge to the center console vents, I used a 3D printed vent piece to hold that gauge there. The HKB steering wheel boss was likely on incorrectly as I sometimes noticed the indicator reset being uneven for left vs. right. In the meantime also installed an airbag delete resistor, as one should. Installed Cube Speed premium short shifter. Feels pretty nice, hope it'll work great too when I actually get to drive. Also put on a fancy Dragon Ball shift knob, cause why not. My buddy was kind enough to weld the rust hole in the back, it was basically rusted through in the lowermost corner of the passenger side trunk area where the wheel arch, trunk panel and rear quarter all meet. Obviously there is still a lot of crustiness in various areas but as long as it's not rusted out I'll just treat and isolate the corrosion and pretend it's not there. Also had to put down a new ground wire for the rear subframe as the original one was BARELY there. Probably a bit controversial depending on who you ask about this... but I ended up just covering the crack in the side of the engine block, the one above the oil feed, with JB Weld. I used a generous amount and roughed up the whole area with a Dremel before, so I hope this will hold the coolant where it should be for the foreseeable future. Did a cam cover gasket job as the half moons were a bit leaky, and there too one could see the people who worked on this car before me were absolute tools. The same half moons were probably used like 3 times without even cleaning the old RTV off. Dremeled out the inside of the flange where the turbine housing mates onto the exhaust manifolds so the diameter matches, as the OEM exhaust manifolds are even narrower than the turbine housings as we all know. Even if this doesn't do much, I had them out anyways, so can't harm. Ideally one would port-match both the turbo and the manifold to the gasket size but I really didn't feel up to disassembling the turbine housings. Wrapped turbo outlet dumps in heat wrap band. Will do the frontpipe again as well as now the oil leak which promted me to tear apart half the engine in the first place is hopefully fixed. Fitted an ATI super damper to get rid of the worn old harmonic balancer. Surely one of the easiest and most worth to do mods. But torquing that ARP bolt to spec was a bitch without being able to lock the flywheel. Did some minor adjustments in the ECU tables to change some things I didn't like, like the launch control that was ALWAYS active. Treated rusty spots and surface corrosion on places I could get to and on many spots under the car, not pretty or ideal but good enough for now. Removed the N1 rear spats and the carbon surrounding for the tailpipe to put them back on with new adhesive as the old one was lifting in many spots, not pretty. Took out the passenger rear lamp housing... what do you know. Amateur work screwed me again here as they were glued in hard and removing it took a lot of force, so I broke one of the housing bolts off. And when removing the adhesive from the chassis the paint came right off too. Thankfully all the damaged area won't be visible later, but whoever did the very limited bodywork on this car needs to have their limbs chopped off piece by piece.   Quite a list if I do say so myself, but a lot of time was spent just discovering new shit that is wrong with the car and finding a solution or parts to fix it. My last problem that I now have the headache of dealing with is that the exhaust studs on the turbo outlets are M10x1.25 threaded, but the previous owner already put on regular M10 nuts so the threads are... weird. I only found this out the hard way. So now I will just try if I can in any way fit the front pipe regardless, if not I'll have to redo the studs with the turbos installed. Lesson learned for the future: Redo ALL studs you put your hands on, especially if they are old and the previous owners were inept maniacs. Thanks for reading if you did, will update when the engine runs again. Hope nothing breaks or leaks and I can do a test drive.
    • No those pads are DBA too  but they have colors too. I look at the and imo the green "street" are the best.
    • I’m not sure what happened I told them about sonic tunes free OTS tune and the next the I know .. I was booted..   To funny 
    • Yea - I mean I've seen my fuel pump which is decades old and uh, while I'm not saying this with real knowledge... but I sure get the ick at using anything in the fuel system that produced the state of that pump. Many years ago I went through multiple pumps (and strainers) before I dropped the tank to clean it out with extreme violence. I'm talking the car would do maybe 50km before coming to a halt, which resulted in me cleaning out the filter with some brake cleaner and going on my way. None of my stuff ever looked like what came out of your fuel tank. I don't think I'd be happy with it unless every single component was replaced (or at least checked/cleaned/confirmed to be clean here).
    • I'm not going to recommend an EBC pad. I don't like them. Just about anything else would suit me better. I've been using Intima pads for a while now.
×
×
  • Create New...