UAS GTR Series 3 Lips... The deal is done!

[meshmesh]

Finally, I have organised a deal with Unique Autosports (UAS) on the Series 3 GTR Lips.

Now, some have had concerns about the quality of the UAS lips.. and going by the lip we received yesterday, it's actually not that bad. the only concern was on the left air vent, the finish could have been better, (which means the panel beater will spend a little extra time to fill it up) the rest of the lip is very nice, even the factory black ripple finish looks awesome. I'll try to organise some pics on Monday, and include the slight imperfections.

John from Unique Autosports (UAS) is offering the following for all SAU forum members: whether you order 1 or 100, there is no waiting for numbers.

$240.00 +(delivery, approx $50-80). (normally $295.00)

Turn around is usually within 2weeks.

So for those lucky enough to be nearby in NSW, that $240.00

All you need to do is mention you saw the offer on SAU forum.

Cheers

Simon

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

CONTACT INFO: (dont forget to mention you saw the deal on SAU)

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Unqiue Autosports

Phone (02) 9634 8000 Fax (02) 9634 8888

Unit A3/2A Victoria Ave, Castle Hill. NSW 2045

NOTE: The pic below is a Genuine GTR Series Lip (~$1300) the UAS Non Genuine Fibreglass Lips is the same minus the blade in the air pockets. As soon as my car is finished I will post up pics.

[Blitz]

Eh?

[Blitz_R33]

any chance of them doing Carbon fibre lips? cos i have noticed they sell alot of cabron bonnets. I would also be interested in a rear centre cabon wing also...

[meshmesh]

Hi Blitz, sorry mate at the momet just in fibre glass, no carbon fibre.. But I have the carbon fibre wing blade on my gtr, which I'll probably be taking off when I sell the car.. Definatley looks horn, and when I do I'll keep you in mind.

[ferni]

I think the carbon fibre blade looks good on the white GTR... but dont think it looks that good on purple

Any photos of the new lip fitted yet Simon?

[meshmesh]

Any photos of the new lip fitted yet Simon?

I am told the car will be ready tomorrow... fingers crossed! Then i'll post some pics.

[ferni]

Cool, will check back tomorrow

[Blitz_R33]

i wonder wat a carbon fibre blade looks like on my black gtr..

[meshmesh]

OK just picked my car.. and have to admit, leaving it in the factory black looks might awesome. Had a chat with my mate the panel beater, and asked him what he thought of the quality of the lip, an how whether it gave hime trouble fitting or not. He reckons he's seen much better finishes, and assumes that the UAS lip mould was probably taken from a busted lip which was pieced together again.

The panel beater spent a bit of time making shaping the lip to make it look schmick, which in the end, both he & I were both rapt about. Overall, the lip looks awesome, and for a measly ~$500, including the lip, delivery, fitting and spraying it was definatley worth it, just pray I don't go scraping out of low driveways..

PS: I just picked the car up, and it's p!issing down rain here in Melbourne. I'll try to take some pics over the weekend.

[meshmesh]

Here's the pic of the front lip on my car..

PS: I opted to keep it stock black finish, but some may want to colour code it.

[Boosted Zed]

We actually bought this mould from QLD and no it is not our normal standard but not too bad. I did mention this though to meshmesh and glad it is all OK. We could do in carbon but might not be too good as tight bends and cost at least twice as much.