Jump to content
SAU Community

Sau Drag Day, 09-04-2016

Cadmoon

By Cadmoon,
in Events

 Share

Recommended Posts

Cadmoon Grand Master

Cadmoon

Posted
Posted

Date: 09-04-2016

Location: WILLOWBANK RACEWAY

Time: 12pm - 2pm

Cost: $60 Paid SauQLD member

$75 Non Paid SauQLD member

This admits the driver and 1 spectator, additional spectators will have to pay.

Spectator Cost: $20Adults, $18 Student with ID & Kids under 13 Free.

All are welcome to stay on after the QLD Event finishes & watch evening Test'N'Tune free.

To run you will need:

Requirements for Car

Helmet to Standard

Long Sleeve Shirt

Long Pants

Covered Shoes

Cars cannot run quicker than 10.00 sec

To run quicker you will need a current ANDRA Licence

All helmets need to be less than 12 years old from Date of Manufacture AND meet one of the following Standards:
SNELL SA2000
SNELL SA2005
SNELL 2000 / 2005
SNELL M2000
SNELL M2005
BS 6658-1985
SFI 41.2A
SFI 31.2A
AS/NZ 1698:2006

Also a lot of people think the helmets with "AS 1698" is the same as "AS/NZ 1698:2006" and its not, they're two different classifications.

13 January 2009 - The helmet regulations have changed, any ANDRA licenced holder is to abide by the current ANDRA rule book at any event. At Test'n'Tunes and Street Series events we will be allowing street vehicles (i.e - non ANDRA licence holders) to still use the AS1698 standard helmet.

Click this link for important new Safety Requirements to run at this event: http://www.willowban...=259&PageID=259

Passenger Rides (cars only)

  • Passenger MUST be 18 years old as a minimum - ID must be shown
  • $20 per passenger - paid at scrutineering
  • Paperwork to be completed at scrutineering
  • Only one passenger permitted in the vehicle at a time
  • Passenger must have approved helmet, long sleeves, long pants and covered shoes
  • Vehicle must have passenger seat, seat belt/harness and windows must be closed
  • The passenger is only permitted to ride in the vehicle he/she has signed the entry form for
  • Vehicles must have a known performance of no quicker than 12.00 seconds.

Payment Details:

Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012

PAYMENT REFERENCE: Username&DragDay

Link to comment
https://www.sau.com.au/forums/topic/462341-sau-drag-day-09-04-2016/
Share on other sites
  • 4 weeks later...
  • 2 weeks later...
  • 4 weeks later...
  • 2 weeks later...
petes-performance Contributor

petes-performance

Posted
Posted

Damn was keen but not yet finished plus rego due today, house payment as well just bad timing for me. I was going for a look though. I know two people with r33's that will b joining soon...so let's all do our best to keep this thing going.

Cadmoon Grand Master

Cadmoon

Posted
  • Author
Posted

I reckon people might b looking to join a club the way cops r getting Hey should I have received something e.g.sticker or membership card for joining I only paid $20?

You should have, how long ago did you join?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      Mistakes were made, my R34 Story

      By MBS206 · Posted

      The oil pressure sensor for logging, does it happen to be the one that was slowly breaking out of the oil block? If it is,I would be ignoring your logs. You had a leak at the sensor which would mean it can't read accurately. It's a small hole at the sensor, and you had a small hole just before it, meaning you could have lost significant pressure reading.   As for brakes, if it's just fluid getting old, you won't necessarily end up with air sitting in the line. Bleed a shit tonne of fluid through so you effectively replace it and go again. Oh and, pay close attention to the pressure gauge while on track!
    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I don't know it is due to that. It could just be due to load on track being more than a dyno. But it would be nice to rule it out. We're talking a fraction of a second of pulling ~1 degree of timing. So it's not a lot, but I'd rather it be 0... Thicker oil isn't really a "bandaid" if it's oil that is going to run at 125C, is it? It will be thicker at 100 and thus at 125, where the 40 weight may not be as thick as one may like for that use. I already have a big pump that has been ported. They (They in this instance being the guy that built my heads) port them so they flow more at lower RPM but have a bypass spring that I believe is ~70psi. I have seen 70psi of oil pressure up top in the past, before I knew I had this leak. I have a 25 row oil cooler that takes up all the space in the driver side guard. It is interesting that GM themselves recommend 0-30 oil for their Vette applications. Unless you take it to the track where the official word is to put 20-50w oil in there, then take that back out after your track day is done and return to 0-30.
    • PranK
      My new to me M35 Stagea wagon

      By PranK · Posted

      Nice, looks great. Nice work getting the factory parts also. Never know when you'll need them.
    • Chupapy
      New r33 owner

      By Chupapy · Posted

      Thanks @jtha7 I will have a look around tomorrow but it is a prick of a spot. These are some photos i tried taking 
    • GTSBoy
      Mistakes were made, my R34 Story

      By GTSBoy · Posted

      I take it that the knock retard is from bearings tapping a little tune? Thicker oil is a fragile bandaid. You need a much bigger oil cooler and probably the bigger pump being discussed.
×
×
  • Create New...