Jump to content
SAU Community

Happy Laps Lakeside Park - 23/04/2016


Recommended Posts

Event:

Happy Laps - Lakeside Park


Description:

A chance to get out on track for a fun cruise and have some om nom noms! Bit of spirited driving is allowed but it is still an event on a race track so a few rules need to be followed (see below). Breakfast will be served with bacon, eggs, beans and toast.


Location:

Lakeside Park



Date:

Saturday the 23rd of April.


Time:

7:00 AM Arrival

7:30 AM Breakfast

8:00 AM On Track


Cost:


$35 for members

$50 for non members



Please note that this is a per person cost, any passengers are required to pay as well.

If you wish to come along to watch and not have breakfast it is free.


Requirements:

1. Participants must meet minimum age requirements for being on track.

2. The overtaking car is responsible for completing the overtaking move safely.

3. Overtaking is only permitted on straights, unless clearly waved passed by the car in front.

4. Overtaking move must be completed well before the end of the straight, and the car being overtaken must be given plenty of room.

5. Cars should not be more than 2 abreast at any point on the track.

6. Be aware of cars around you, in front and behind (and beside when being overtaken).

7. Do not assume that the car in front of you knows you are there.

8. Please pay cash on the day, no EFTPOS is available.


Lakeside Specific Rules:

9. No overtaking or cars side by side on the kink.


Payment Details:


Name: Skylines Australia Queensland Club

Bank: Westpac

BSB: 034 063

ACC: 354012


PAYMENT REFERENCE: Username&HappyLaps

Link to comment
https://www.sau.com.au/forums/topic/463276-happy-laps-lakeside-park-23042016/
Share on other sites

  • 3 weeks later...
  • 3 weeks later...

Beauty I'm keen to race him

Have you ever been to LP? There isn't any opportunities to race people because it's mostly corners.

What's the licensing requirements at QR this year? Do they apply to Lakeside?

No licence requirements yet.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
    • You have a knack for photography my friend. It makes the 86 look like a complete bucket. The 34 went with you to Europe and back. It's special. (we all feel the same about our 'shitboxes' that every bystander seems to absolutely love)
    • It's been quite the ordeal but hey, at least you figured it out.
    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
×
×
  • Create New...