Jump to content
SAU Community

4wd And A-lsd Lights On(bnr34vspec)

IsaacBNR34Vspec
 Share

Recommended Posts

IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
Posted

Hi everyone,im new here and a helpfull assist would be much appreciated..

I have a BNR34Vspec 2001 and facing a problem tat after my car came to a fullstop,after a few seconds my 4wd and A-LSD lights got turn on..after restarting it again everything went normal and it got turn on again after a few second of fullstop..ive checked the resovoir behind the rear boot and fluid are at the max level..ive been tru and read forums but couldnt find a problem that happenned exactly like mine..

I wish to try solving it myself so is there any idea where i can start from?

Help and assist are most appreciated and pls to meet everyone here since im new here and also new to my car

Cheers everyone!!

Link to comment
https://www.sau.com.au/forums/topic/463322-4wd-and-a-lsd-lights-onbnr34vspec/
Share on other sites
IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
  • Author
Posted

I did tried finding the spot to read ecu code behind the boot and ended up clueless where its is..tru reading from forums reading ecu codes from boot isnt it apply only for r32 and r33?

Thanks for the reply Hadouken :)

IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
  • Author
Posted

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Meathead Collaborator

Meathead

Posted
Posted (edited)

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Yeah with the engine switched off start it and keep the rpm 1000 and above for a few minutes and see if the Alsd light is on, if it is not and you let it come back to idle does the Alsd light illuminate after a while again ?

You may have a fluctuating idle that goes below normal and sends a low TPS signal to the Atessa cu which will cause the alarm

TPS signal to Atessa on my r33 gtr vspec is 0.3 - 3.7 v if it falls outside of this it will fault.

You could check the AAC valve (under plenum - 4 bolts and a plug) give it a clean and renew the joint. Idle can be adjusted with the screw.

Lots of AAC cleaning threads here in SAU to help you.

If you are not sure get someone else to do it, preferably a friend as a shop will probably sting!

I am not saying this is your problem but it could be. Might be dirty plugs also causing hunting.

Good Luck!

Edited by Meathead
Meathead Collaborator

Meathead

Posted
Posted
How tf is hunting and dirty plugs related to a 4wd light?[/quote

Hey tf your mouth runs before your brain

You should question other posters in a more civil way.

Tps is directly proportional to rpm which signal inputs to atessa tf

If you could not figure that out then maybe you should just pull your head in tf

IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
  • Author
Posted

Meathead:ive tried as u intructed..like revving above 1000rpm..the lights did not turn on..but as i let go the acceleration my rpm idle show slightly above 1000rpm,is tat a normal?

BTW,wat AAC valve means..?sorry for a noob question..trying to learn as much as i can

Thanks for the reply and point outs..

Meathead Collaborator

Meathead

Posted
Posted

Not the obvious culprits then.

You should seriously see what fault code is coming up, lots of things can trigger this. ie wheel speed sensors for one.

Regarding far fetched - not at all mate Atessa takes rpm signal also and if the rpm signal fluctuates below a certain range say from hunting caused by fouled plugs it will error. \

IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
  • Author
Posted

Count grantleyish:the 4wd and A-LSD comes on whenever the car come into fullstop...i didnt time lap how long it needs to be driven to alarm the lights to go on..as if itll turn on as long as car stop moving and after few seconds..it came on..

IsaacBNR34Vspec Rookie

IsaacBNR34Vspec

Posted
  • Author
Posted

Meathead:yeah,mayb ill take your advise and do a scan just like GTSBoy suggested...but before goin into that i would like to gv a bleed to the attesa system fot any trap air..will update see if this gonna work..cheers everone and thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Tomei gasket

      By joshuaho96 · Posted

      I've heard the Tomei USA head gaskets are decent if you want to o-ring the heads but otherwise not recommended.
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      The 296mm rotors are the R33 turbo brakes. The 310mm rotors are the R34 turbo brakes. The calipers are nearly the same, but not. They're the same caliper but the R34 caliper has longer legs so that it sits out far enough to go over the rotor. The pads are the same for both. When you say, "I bough tsome EBC"....did you just mean pads? Or rotors? 310mm rotors fit under 17" wheels. There may be some wheels without enough clearance though. I can't fit my fingers between the barrel of my wheel and the "corners" of my R34 calipers, but there is plenty of room behind the spokes. This is on Enkei RPF1. You can fit 324mm rotors inside a 17" wheel, but I'd be willing to bet that it would be close to impossible with the Nissan/Sumitomo caliper (using an adapter, of course), because the Sumitomo caliper is fatter than the Brembo caliper that is supposed to go on the 324mm rotors.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      Hi. Can someone tell me what brakes(and mainly WHERE) can i buy brakes on R34 GTT? I bought some EBC which SHOULD go on my car(i have GT but it has GTT brakes) but it does not fit, Brakes are "too" small(296mm) Are 310mm be good or? I have 17 inch wheel so no "big boys" but for me driving i just need one that fits and i can get here in EU/Czech.
    • Marek
      Hi everyone.

      By Marek · Posted

      Since winter isn't that harsh anymore in Poland, i will definetely drive it 365 days a year 😉. But if the snow hits i will try it for sure and let U know. Only swap i am planning to do is of course R34 GTR front 😍.
    • Marek
      WGNC34 - floor mats

      By Marek · Posted

      Hey. Very valuable information about pitwork, I will pay attention when buying any consumable parts 🙏 As for the carpets - I got a handful of information from nengun, from which it appears that indeed the carpets for the driver's side are OEM. They are not able to show me any pictures due to the long chain of different sales entities but after I place the order, as soon as the goods arrive at the nengun warehouse from which they will send the shipment to me they can send me photos and if my purchase differs from OEM I can immediately return it / cancel the purchase. I think I will give it a try 😉. Of course i'll let you know what's what as soon as i get them P.s. I know the topic is not relevant to the thread, but both nengun and amayama have these SICK 😍 trunk room lamps available. Do you know anyone who ordered them? I need to have one in my car
×
×
  • Create New...