Jump to content
SAU Community

Recommended Posts

Hi everyone,im new here and a helpfull assist would be much appreciated..

I have a BNR34Vspec 2001 and facing a problem tat after my car came to a fullstop,after a few seconds my 4wd and A-LSD lights got turn on..after restarting it again everything went normal and it got turn on again after a few second of fullstop..ive checked the resovoir behind the rear boot and fluid are at the max level..ive been tru and read forums but couldnt find a problem that happenned exactly like mine..

I wish to try solving it myself so is there any idea where i can start from?

Help and assist are most appreciated and pls to meet everyone here since im new here and also new to my car

Cheers everyone!!

Link to comment
https://www.sau.com.au/forums/topic/463322-4wd-and-a-lsd-lights-onbnr34vspec/
Share on other sites

I did tried finding the spot to read ecu code behind the boot and ended up clueless where its is..tru reading from forums reading ecu codes from boot isnt it apply only for r32 and r33?

Thanks for the reply Hadouken :)

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Meathead:u mean after the lights turn on,shut off the and turn on the engine and give it a 1000rpm and see if the lights are on again?ok ill gv it a try by tis evening..if lights still turn on after wat u intruct me to do means theres a TPS failure right?do correct me if im wrong

Thanks for the reply ill update after ive try it out.cheers

Yeah with the engine switched off start it and keep the rpm 1000 and above for a few minutes and see if the Alsd light is on, if it is not and you let it come back to idle does the Alsd light illuminate after a while again ?

You may have a fluctuating idle that goes below normal and sends a low TPS signal to the Atessa cu which will cause the alarm

TPS signal to Atessa on my r33 gtr vspec is 0.3 - 3.7 v if it falls outside of this it will fault.

You could check the AAC valve (under plenum - 4 bolts and a plug) give it a clean and renew the joint. Idle can be adjusted with the screw.

Lots of AAC cleaning threads here in SAU to help you.

If you are not sure get someone else to do it, preferably a friend as a shop will probably sting!

I am not saying this is your problem but it could be. Might be dirty plugs also causing hunting.

Good Luck!

Edited by Meathead
How tf is hunting and dirty plugs related to a 4wd light?[/quote

Hey tf your mouth runs before your brain

You should question other posters in a more civil way.

Tps is directly proportional to rpm which signal inputs to atessa tf

If you could not figure that out then maybe you should just pull your head in tf

Meathead:ive tried as u intructed..like revving above 1000rpm..the lights did not turn on..but as i let go the acceleration my rpm idle show slightly above 1000rpm,is tat a normal?

BTW,wat AAC valve means..?sorry for a noob question..trying to learn as much as i can

Thanks for the reply and point outs..

Not the obvious culprits then.

You should seriously see what fault code is coming up, lots of things can trigger this. ie wheel speed sensors for one.

Regarding far fetched - not at all mate Atessa takes rpm signal also and if the rpm signal fluctuates below a certain range say from hunting caused by fouled plugs it will error. \

Count grantleyish:the 4wd and A-LSD comes on whenever the car come into fullstop...i didnt time lap how long it needs to be driven to alarm the lights to go on..as if itll turn on as long as car stop moving and after few seconds..it came on..

Meathead:yeah,mayb ill take your advise and do a scan just like GTSBoy suggested...but before goin into that i would like to gv a bleed to the attesa system fot any trap air..will update see if this gonna work..cheers everone and thanks

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • My guesstimate, with no real numbers to back it up, is it won't effect it greatly at all.its not a huge change in position, and I can't see the air flow changing from in turbulence that much based on distance, and what's in front of it. Johnny and Brad may have some more numbers to share from experience though.
    • Which solenoid? Why was it changed? Again, why was this done? ...well, these wear..but ultimately, why was it changed? Did you reset the idle voltage level after fitment? I'm just a tad confused ~ the flash code doesn't allude to these items being faulty, so in my mind the only reason to change these things, would be some drive-ability issue....and if that's the case, what was the problem? Those questions aside, check if the dropping resistor is OK ...should be 11~14 ohms (TCU doesn't throw a flash code for this) ~ also, these TCU designs have full time power (to keep fault code RAM alive), and I think that'll throw a logic code (as opposed to the 10 hardware codes), if that power is missing (or the ram has gone bad in the TCU, which you can check..but that's another story here perhaps).
    • Question for people who "know stuff" I am looking at doing the new intake like the one in the picture (the pictured is designed for the OEM TB and intake plenum), this design has the filter behind the front bar, but, the filter sits where the OEM duct heads into the front bar, and the standard aperture when the OEM ducting is removed allows the filter to pulled back out of the front bar into the engine bay for servicing, a simple blanking plate is used to seal the aperture behind the filter This will require a 45° silicone hose from the TB, like the alloy pipe that is currently there, to another 45° silicone hose to get a straight run to the aperture in the front bar Question: how will it effect the tune if I move the MAF about 100-150mm forward, the red is around where my MAF is currently, and the green would be where it would end up Like this This is the hole the filter goes through  Ends up like this LOL..Cheers    
    • Despite the level up question, actually I do know what that is....it is a pressure sender wire.  So check out around the oil filter for an oil pressure sender, or maybe fuel pressure near the filter or on the engine. Possibly but less likely coolant pressure sensor because they tend to be combined temp/pressure senders if you have one. Could also be brake pressure (in a brake line somewhere pre ABS) but maybe I'm the only one that has that on a skyline.
    • Pull codes via the self-diagnosis procedure. As far as I can tell this is just a sign of transmission issues but not a code unto itself.
×
×
  • Create New...