Jump to content
SAU Community

Recommended Posts

Hi guys i have two items for sale, both are made for R34 chassis but im sure you can make it fit other skylines with small modifications.

1. Custom made 4 inch exhaust system with OVAL piping to maximise ground clearance (Same piping used on v8 supercars and NASCARS) with discreet dual tip XFORCE 4 inch muffler and TWIN 3 inch Metal Cat high flow cats. Custom Ceramic coated exhaust manifold and dump pipe.(Ceramic coated from dump to cats) [All ceramic coating by Chris at Craved Coatings in a Satin Black finish]

Best thing about this system is that it dosn't hang lower than the rails, so you can lower your car more and moree and still be legal :D

Costed over 3k to make. Looking for $900 (It's brand new with no dents or damage)

Would be awesome on single turbo GTRs or GTT/GTST.

I know as a fact that r33 exhaust is a bit shorter so to fit it on all you have to do it shorten it a bit from where the cats are.

You could also fab some work the match it with the twin turbo down pipe.

2. HKS CHROMOLY half bolt in cage with side intrusion bars and fully paded. Suits R34 sunroof model. Missing the cross bar but wouldn't cost much to replace it as its just a straight pipe.

$550

Contact me on 0450 232 121

Melbourne but can post at buyer's expense.

post-72334-0-92880900-1457611863_thumb.jpg

post-72334-0-71473100-1457611864_thumb.jpg

post-72334-0-00224900-1457611866_thumb.jpg

post-72334-0-35998200-1457611867_thumb.jpg

post-72334-0-27850900-1457611869_thumb.jpg

post-72334-0-09373400-1457611875_thumb.jpg

post-72334-0-51067900-1457611878_thumb.jpg

post-72334-0-63216500-1457612002_thumb.jpg

post-72334-0-59283500-1457612072_thumb.jpg

post-72334-0-50471000-1457612139_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah I've had too many issues with knock off's on the BMW's. I don't want to do a job twice or more because the parts are shit.
    • I read this and thought "ah! I will do this scissor jack on the tow point thing!" I just use my floor/low profile/costco jack and lift the car up by the tow hook itself, then slide jack stands under. Never thought about using scissor into floor jack combo :p
    • Well, my new WMI system took much longer to finalize. I actually missed my dyno appointment last Friday and lost my 150$ deposit. I'll be going back in the next week or two.  To sum it up. I only kept the AEM tank from my old setup. I replaced the AEM pump with a higher flow/pressure ProMeth 30GPH pump. I also swapped over to a 6AN low pressure feed line to the pump from the tank. There's also a pressure switch you cannot see on the pump high pressure line.    This is feeding 6x 200CC direct port nozzles and 1x 500CC Pre Throttle body nozzle. All fittings are Swagelok, because well why not. I also have a 300PSI pressure sensor up front.    I now have my Haltech ECU controlling everything. I start my pump with a basic relay at 5PSI and deadhead it. I then PWM a 3000CC methanol Injector to control flow starting around 10psi. The pressure switch in the trunk, along with my tank level are safeties before I ever get to 10PSI, and then I use my pressure sensor upfront as a secondary safety to cut the WMI and corrections in case the injector blocks or a line ruptures.  Wish me luck on the dyno!    
    • So, I'm back with bad news. There's no jack long enough on this planet that will reach the front subframe. If by some chance there is, it would weigh 200lb's.  I purchased a long reach jack... The damn thing weighted 120lb's and was massive. Didn't even come close, was still short at least a foot. It was a pain, but I brought it back. Next I decided HA! No problem, I'll get an Extra long reach jack. Well, I couldn't lift the box... It must have weighed 160LB's and luckily there was an open box in store. I took measurement and was still nowhere close.  Sadly I've lost hope and have accepted defeat. 
    • Thanks for that tip, niZmO_Man. I think the battery is OK. It's quite a new one, but I'll check. Last time I needed a new battery, everything electronic was fine, except that there wasn't enough current to turn over the starter. I decided to order one of the partial AV system translation CDs from Car Audio Workshop in NZ. That might have some effect, or help me diagnose the date problem. 🤞
×
×
  • Create New...