Jump to content
SAU Community

Recommended Posts

  • 3 weeks later...

As per the topic i have a brand new unopened Nissan S15 OEM tie rod end for sale

KMS want $77 plus post but i will sell it for $60 including shipping Aus wide or pickup is available on the northside of Brisbane

Cheers

Contact via pm thanks

Part number 48520-50Y25

Edited by Gts30t
  • 1 month later...
  • 1 month later...

For sale is my Apexi Power FC D-Jetro with EL hand controller and 2 x map sensors and wiring to suit BNR34.

The unit is in perfect condition and has only been used for about 25-30k kms. Comes with the newer and much better EL hand controller.

This D-Jetro model does away with the air flow meters and the cost involved with buying bigger ones such as Nismo or Z32 units :cool:

Price is $750

Itemis located on Brisbane northside for pickup or will post at buyers expense.

 

Oem center console, no lid, bit rough could do with a fresh coat of paint if picky $20

Oem stereo/ac/gearstick surround $20

Oem airbox snorkel, getting rare $50

Also RHS and LHS inner door handles available $20 for both

Accel pedal rubber and arm $10

Brake and clutch pedal rubbers $5 each

S15 OEM tie rod end for sale $50

 

 

Edited by Gts30t

Airbag sold! 

 

Revised list

Apexi Power FC D-Jetro with EL hand controller and 2 x map sensors and wiring to suit BNR34. Perfect condition $675

blitz rb26 stainless front pipes, great condition $250

hpi clear rb26 cam gear cover, great condition $100

100 cell racing cat, suit bnr34, great condition $100

Cat sold

Revised list

Apexi Power FC D-Jetro with EL hand controller and 2 x map sensors and wiring to suit BNR34. Perfect condition $650

blitz rb26 stainless front pipes, great condition $225

hpi clear rb26 cam gear cover, great condition $100

 

image.jpeg

image.jpeg

image.jpeg

image.jpeg

Bump

Apexi Power FC D-Jetro with EL hand controller and 2 x map sensors and wiring to suit BNR34. Perfect condition $650

blitz rb26 stainless front pipes, great condition FINAL PRICE DROP $200

hpi clear rb26 cam gear cover, great condition $100

 

Clear cam cover sold! 

Apexi Power FC D-Jetro with EL hand controller and 2 x map sensors and wiring to suit BNR34. Perfect condition FINAL PRICE DROP $650

blitz rb26 stainless front pipes, great condition FINAL PRICE DROP $200

 

 

image.jpeg

image.jpeg

image.jpeg

  • 2 months later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...