Jump to content
SAU Community

Recommended Posts

All parts pick up from glenfield or Smithfield NSW will post buyer covers postage costs

Will do a little cheaper if you buy a couple of things

All things are brand new and genuine (except coilpacks used for one drive 25kms work perfect removed as car was sold repacked in box and clean)

- Used for a 10 minute drive still brand new Splitfires $500

- Brand new genuine jecs Z32 $300

- Brand new genuine Tomei plug $40

- Brand new genuine Apexi pod $150

- Brand new genuine Walbro 460l $200

- Genuine oem brand new O2 sensor $200

- Nrg quick release and short hub with lock $300

- Brand new Gizzmo ms ibc v3 boost controller $270

Adjustable arms

Most Fit R32/r33/r34 s13/s14/s15 180sx a31 300zx cefiro

Perfect for 180/s13/r32 setup as not all parts fit the above model would have to check before hand

- Caster and lcas $270 (definitely r32/r33 z32 300zx s13/180sx)

- Traction rods $90 (all the listed models)

- Upper camber arms front $160 (r32/z32 would have to check others)

- Upper camber arms rear $100 (r32/z32 would have to check others)

- Rear lca $180 (definitely r32/r33 s13/s14/s15 a31 cefiro)

$750 the lot together.

post-108512-14640918306953_thumb.jpg

post-108512-14640918564379_thumb.jpgpost-108512-14640918646867_thumb.jpg

post-108512-1464091875173_thumb.jpgpost-108512-14640918835652_thumb.jpgpost-108512-14640918922999_thumb.jpgpost-108512-14640919023846_thumb.jpgpost-108512-14640919096594_thumb.jpgpost-108512-14640919173719_thumb.jpg

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ok so if i wanted to go 18's i would go for 8's  in front 30+ or 32+ off set at front and the back 9 would be ok? what offset should i aim for.. then can i do some  hunting for wheel rim choices..   
    • Absolute f*cking nightmare. I had to take breaks constantly, and I was always pissed off when I got home. The line split in Italy on day 2 (we drove from the Netherlands), lol. Driving any narrow European town was... well, sh*t.   Appreciate it man. Here, I'll just drop a favourite from the load I took on Saturday.   I'll update here when things happen with the car, the thing is, with stock power and almost everything chassis-wise taken care of, there really are no problems. 268,000kms now and counting.  
    • Ah! I actually managed to snag a lightly used set.... that aren't so suitable for me right now. They don't work on a GTT without some cutting or creative heat moulding. I thought about reselling them myself cause I didn't want to murder them, but it looks like I'm probably going to attempt to murder them/melt them because I may as well. @GTSBoy @PranK can somebody close this thread?
    • Hey mate,  I have a set, one is slightly damaged but wont be noticable once installed.  Shoot me a message if your still after them 
    • I couldn't wait But, the black constant tension hose clamps were too thick and there wasn't enough clearance at the T/B and I couldn't get it to seat properly, so I had use a silver one there I also added some 3" silicone over the alloy bit that goes through to hole on the radiator support as it looked like it was sitting on the edge of the hole in the radiator support, I never noticed a rattle or anything, but there was a witness mark It is basicly done, and I can live with the silver hose clamp at the T/B, I will get a black clamp for the head vent though where it is attached to the bulkhead fitting  It never stops...LOL, only issue now with the shock tower brace is it slightly touches the under bonnet liner now, if I leave it it will either wear some paint off the brace where it touches, or damage the liner, so I removed the liner to see what I have to work with, with the liner removed I have about 20mm of clearance, but sadly the middle part of the underside of the bonnet is only dusted with paint and looks crap, so I cannot have that, but.... as I have a roll of Carbuilders premium under bonnet insulation in the garage laying around that is only 5.5mm thick (we were going to use it on the boys Patrol, but he crashed the front of it a few months and it was written off, hence why he now drives my old Honda Accord Euro), I'll use the OEM liner as a template and get the Carbuilders stuff fitted up to cover that dusted paint up
×
×
  • Create New...