Jump to content
SAU Community

Wanted: RB26 Pistons

carterr32

By carterr32,
in Wanted to Buy

 Share

Recommended Posts

Duncan Grand Master

Duncan

Posted
Posted

This is probably going to sound odd....but assuming you are doing a rebuild but want to keep the price down, check out the cost of brand new pistons and rings from nissan, they were quite reasonable last I checked.

Also FWIW, rods are generally reusable (and will be obvious if they aren't), and so is the oil pump unless the motor spun a bearing. Second hand oil pumps are a minefield because its hard to tell if they are in good condition

carterr32 Rookie

carterr32

Posted
  • Author
Posted

Yeah sort of, going to try 26 internals in 25 block so just a mockup/low cost rebuild as a test to make sure its going to work, pistons are the main thing I need at this stage I think I seen new OEM pistons were about 100-150ea so not far off just going forged but a bit more than I would like to spend considering its just a trial at this stage.

As for the oil pump I accidentally broke the housing.

  • 2 weeks later...
  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • TurboTapin
      Why am I hitting a power wall with my stroked RB25?

      By TurboTapin · Posted

      Kelford 246-A2. 262in/272ex. 
    • Adam_ECR33
      Hello sau 👋

      By Adam_ECR33 · Posted

      Thank you, 100% the intent. New coils were due and the 17" sixers look/feel loads better than the stock wheels. The aero options are so spot on.   Thanks for the warm welcome, all!
    • JC71
      98 R34GTT 4k engine stumble

      By JC71 · Posted

      98 r34 gtt Been rocking my latest setup and car running like never before. Have put a good 200 miles on it since all the latest changes and additions. everything is dialed in and have been driving it a bunch.   However, all a sudden last weekend as soon as I pushed throttle passed 4k and the engine stumbles, (slow or fast acceleration) hesitates and doesn’t go above 4100 or so, like a misfire. Everything else seems fine. I had a “good” set of coil packs that I removed from car when I first got it when I changed them over to new coils. I swapped out current ones for those, but no change. I also changed the plugs, no change. Seems to rev over 4 when out of gear with no load just fine no “misfire”, but as soon as its in gear with a load of any kind, it “misfires” as soon as rpm drop back below 4 k it runs perfectly, smooth, starts, restarts and drives fine as long as I keep it below 4 k while in gear. All readings look fine, no CEL   Any idea as to what could all a sudden cause an issue when pushing rpms passed 4 k?
    • r32-25t
      Why am I hitting a power wall with my stroked RB25?

      By r32-25t · Posted

      When you say your cams are 272/262 is that 272in and 262ex?
    • Kinkstaah
      Nismo GT Pro LSD configurations

      By Kinkstaah · Posted

      We're arguing semantics. I am saying 45 accel and a 55 deccel ramp are "2 ways". Even a 45 degree ramp and an 89 degree ramp is "2 ways", because it is literally... two ways. The cusco 55/30 ramp is a 2 way. It's two ways. I get it though - in normal nomenclature a "2 way" would be 45/45 or 55/55 or 60/60 i.e the same locking in both directions. And something like 45/65 would be considered "1.5 way". I would then say if we're getting into the nitty gritty then every locking diff is a "2 way" diff and we should not speak in 1.5, or 2 ways but ramp angles instead. Which ofc if one of those ramp angles is 90deg, that side is not doing any locking. :p So Nismo don't obviously sell 3 things. The fact of the matter that they only sell two items really goes to show that there's a 2 way and a "1,5 way" which is really a 1 way. I believe the actual lockup for the 'adjustability' of the GT pro is really just setting preload for when the ramps actually start locking up. It's not changing how much 'wayness' there is. It is (somehow) horribly explained. People just buy whatever diff and go "locks up good bruh" and that's what ends up on socials forever.  
×
×
  • Create New...