Jump to content
SAU Community

Recommended Posts

Hi All,

Hoping for some advice as I have lost hope after about 30mins lol

So the issue developed about 2 weeks ago when I moved it to wash.

Moving in / out the driveway and sitting idle I could hear a very low constant beep noise, at first I thought it was the turbo timer but nope it's def not that.

I have stuck my head all through out the dash around the drivers side, the best location is above the left knee around the steering column but I still can't locate it. It's a very low pitched beep and if you were sitting in the passenger seat you probably wouldn't hear it.

It also was not present prior to hearing it.

Any help is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/466229-low-faint-beeping-noise-r33-s2/
Share on other sites

Check for a small speaker looking unit behind the drivers side door card

other thought was an aftermarket alarm with a dead/dying roll of watch batteries

perhaps even a hidden turbo timer behind the dash

  • Like 1
  • 2 weeks later...

Depending on the sound it could be some sort of earthing issue. I know that one of my old cars made a low pitch whine when it was started. It varied with the RPM of the engine. 

One thing I can suggest is to double check your terminals on the battery (assuming you don't have two). Make sure they are super clean and tight. If your car has a separate earthing point to the chassis (normally located either at the front of the car or near the strut towers), check the earth. If this is in poor shape you can introduce all sorts of odd harmonics.

The other sound that it could be is a dying capacitor. They make a funny squealing sound when they are dying. Do you have any electronics (PCBs) mounted in the area that could be the source? 

^^^ That said if you are absolutely sure this is a beep and not some spurious noise, you need to look for electronic boards. You will most likely be hearing a piezo speaker. These are generally smaller than a 5 cent piece and are mounted within electronics, so are hard to hear. 

Most smart (read: well designed) items will start to beep if the board detects a lack of power. 

Quote

dead/dying roll of watch batteries

This is most likely the reason, most of the circuit will be receiving 12V (or thereabouts) from the car and will operate fine, but the backup battery (normally a lithium watch or button battery) may run on a different area of the board with it's own power sense circuit. When the power drops the circuit will move from it's normal mode of operation, to a circuit that include the speaker, thereby creating the beep. 

I'm not familiar with enough of the R33 electronics or any of the aftermarket items to know what it could be, but you may find it's as silly as the clock or radio in the car.

I'd suggest (if it bothers you enough) to pull off any trim in the area and try to isolate the sound. It could be coming from deep within your dash.

Yes that's the stumping part.

Only when the car is on it beeps.

It's comes from around the steering column.

I'm going to spend some more time on it as I noticed the greddy control boxes are shoved around in there ( I assume control boxes for boost and oil temp gauge ) I seem to have a sneaky suspicion it may be either of them cause that's the only items in the vicinity.

Also ripped out the turbo timer and still doing it.


  • 3 months later...
  • 7 months later...
  • 1 year later...

Any solution to this ? I have similar situation in my skyline V35, 3 beeps at ~1 every 2 sec interval even without keys inserted, lower than the sound it makes when I leave the keys in with door open. Does not make the beep sound when I have car running though. 

Edited by kool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...