Jump to content
SAU Community

Low / Faint beeping Noise R33 S2

ADM33T
 Share

Recommended Posts

ADM33T Explorer

ADM33T

Posted
Posted

Hi All,

Hoping for some advice as I have lost hope after about 30mins lol

So the issue developed about 2 weeks ago when I moved it to wash.

Moving in / out the driveway and sitting idle I could hear a very low constant beep noise, at first I thought it was the turbo timer but nope it's def not that.

I have stuck my head all through out the dash around the drivers side, the best location is above the left knee around the steering column but I still can't locate it. It's a very low pitched beep and if you were sitting in the passenger seat you probably wouldn't hear it.

It also was not present prior to hearing it.

Any help is appreciated.

Link to comment
https://www.sau.com.au/forums/topic/466229-low-faint-beeping-noise-r33-s2/
Share on other sites
Sinista32 Grand Master

Sinista32

Posted
Posted

Check for a small speaker looking unit behind the drivers side door card

other thought was an aftermarket alarm with a dead/dying roll of watch batteries

perhaps even a hidden turbo timer behind the dash

  • Like 1
  • 2 weeks later...
Steve85 Mentor

Steve85

Posted
Posted

Depending on the sound it could be some sort of earthing issue. I know that one of my old cars made a low pitch whine when it was started. It varied with the RPM of the engine. 

One thing I can suggest is to double check your terminals on the battery (assuming you don't have two). Make sure they are super clean and tight. If your car has a separate earthing point to the chassis (normally located either at the front of the car or near the strut towers), check the earth. If this is in poor shape you can introduce all sorts of odd harmonics.

The other sound that it could be is a dying capacitor. They make a funny squealing sound when they are dying. Do you have any electronics (PCBs) mounted in the area that could be the source? 

Steve85 Mentor

Steve85

Posted
Posted

^^^ That said if you are absolutely sure this is a beep and not some spurious noise, you need to look for electronic boards. You will most likely be hearing a piezo speaker. These are generally smaller than a 5 cent piece and are mounted within electronics, so are hard to hear. 

Most smart (read: well designed) items will start to beep if the board detects a lack of power. 

Quote

dead/dying roll of watch batteries

This is most likely the reason, most of the circuit will be receiving 12V (or thereabouts) from the car and will operate fine, but the backup battery (normally a lithium watch or button battery) may run on a different area of the board with it's own power sense circuit. When the power drops the circuit will move from it's normal mode of operation, to a circuit that include the speaker, thereby creating the beep. 

I'm not familiar with enough of the R33 electronics or any of the aftermarket items to know what it could be, but you may find it's as silly as the clock or radio in the car.

I'd suggest (if it bothers you enough) to pull off any trim in the area and try to isolate the sound. It could be coming from deep within your dash.

ADM33T Explorer

ADM33T

Posted
  • Author
Posted

Yes that's the stumping part.

Only when the car is on it beeps.

It's comes from around the steering column.

I'm going to spend some more time on it as I noticed the greddy control boxes are shoved around in there ( I assume control boxes for boost and oil temp gauge ) I seem to have a sneaky suspicion it may be either of them cause that's the only items in the vicinity.

Also ripped out the turbo timer and still doing it.


  • 3 months later...
  • 7 months later...
  • 1 year later...
kool Newbie

kool

Posted
Posted (edited)

Any solution to this ? I have similar situation in my skyline V35, 3 beeps at ~1 every 2 sec interval even without keys inserted, lower than the sound it makes when I leave the keys in with door open. Does not make the beep sound when I have car running though. 

Edited by kool

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...