Jump to content
SAU Community

New guy with M35

RSXVRider

By RSXVRider,
in Four Door Family & Wagoneers

 Share

Recommended Posts

RSXVRider Apprentice

RSXVRider

Posted
Posted
New guy with M35

Hey guys,

I've just bought my first stagea after wanting one for ages. M35 bone stock apart from a set of rims.

I love it. It needs a few things doing to it but that's half the fun.

It came with a full service history so I hope it's been looked after.

The one problem I do have and I have read EVERY post in here about it is my 4WD light is on.

what makes this so different? Well after reading a thread in here on how to clear codes (turn on, press acc pedal 5 times etc) my light goes off. I drive it and I have functioning 4WD (split torque gauge works).

BUT when I re start the car [normally] the light will be on so I'll turn car off, go through the code clearing actions and BooM, all good ????

My intention is to try the relay under the airbox , failing that I'll bleed the lines of any air.

Has anyone else had what I have described ?

Link to comment
https://www.sau.com.au/forums/topic/466787-new-guy-with-m35/
Share on other sites
RSXVRider Apprentice

RSXVRider

Posted
  • Author
Posted

Thanks Josh.

Thanks to all the information in this forum that was the first thing I checked. Currently my level is just above full.

Would that amount prevent the pump from pressurizing the system?

Also do you have any idea as to why I can clear the code and it works fine only for the code to return?

I'm reading all about how our cars are NOT OBDII so clearing them could be a hassle.

West Grand Master

West

Posted
Posted
55 minutes ago, RSXVRider said:

Thanks Josh.

Thanks to all the information in this forum that was the first thing I checked. Currently my level is just above full.

Would that amount prevent the pump from pressurizing the system?

Also do you have any idea as to why I can clear the code and it works fine only for the code to return?

I'm reading all about how our cars are NOT OBDII so clearing them could be a hassle.

I don't have a stag yet but about to own one. Has done a bit of researching on this issue as well as the car i'm getting having the same problem.

By the sound of it, if any luck, a flush + new fluid my help you. There is also a big fuse (?) (20amp) somewhere that can be replace to fix the issue as well. If all of those mentioned still dont' fix it, better start sourcing a secondhand unit as the $2 pressure switch (built in) is known to fail and Nissan won't sell them separate.

West Grand Master

West

Posted
Posted
1 hour ago, RSXVRider said:

Thanks west.

Well ive just found out that if i start the car with the synchro switched on i dont get the 4WD light on.
Fully functional 4WD.
Weird right.... lol.

Have heard of that as well but i'm afraid it's only a band-aid fix and not a long term solution, then again i could be wrong, only interpreting what i have read so far.

RSXVRider Apprentice

RSXVRider

Posted
  • Author
Posted

So i put my new relay in.
Statyed car. No 4ws light.
Small deive light stays off. Winning.
Turn car off.
Turn car on. Boom. 4wd light on again. Hmmmmmm.

Can anyone tell me what fuse is the 4wd? There are some big ones bwhind the battery but noting is labeled

Daleo Grand Master

Daleo

Posted
Posted

It sounds like a pressure switch fault mate; very common. The best thing to do would be to get it on a scantool, and find out 100% what the fault is.

The fuse (it's more a fusible link) for the ATTESSA pump is in the block in front of the battery. 

It's labelled ETS from memory.

RSXVRider Apprentice

RSXVRider

Posted
  • Author
Posted

Thanks West. I hadn't seen that thread before.

I did try the disconnect single wire to the pump to bleed it but the pump wouldn't activate.

I'm going to give it another go on the weekend as i just read on another tread that you're supposed to bleed the gearbox nipple. I was attempting to bleed the ATTESSA pump nipple.

Plus one tread says to disconnect then bleed where as another one says to disconnect then re-connect straight away to bleed.

West Grand Master

West

Posted
Posted
15 hours ago, RSXVRider said:

Thanks West. I hadn't seen that thread before.

I did try the disconnect single wire to the pump to bleed it but the pump wouldn't activate.

I'm going to give it another go on the weekend as i just read on another tread that you're supposed to bleed the gearbox nipple. I was attempting to bleed the ATTESSA pump nipple.

Plus one tread says to disconnect then bleed where as another one says to disconnect then re-connect straight away to bleed.

From this thread?

 

RSXVRider Apprentice

RSXVRider

Posted
  • Author
Posted

So after re reading all the threads I managed to work out the correct way to bleed the ATTESSA pump.

There was a ton of huge air bubbles in the line so I was quietly confident that was my problem.

I flushed the entire system with new fluid just to find my light is still on ..... Grrrrrrr

Well at least I know my pump actually works...

West Grand Master

West

Posted
Posted
7 minutes ago, RSXVRider said:

So after re reading all the threads I managed to work out the correct way to bleed the ATTESSA pump.

There was a ton of huge air bubbles in the line so I was quietly confident that was my problem.

I flushed the entire system with new fluid just to find my light is still on ..... Grrrrrrr

Well at least I know my pump actually works...

So what's your method of doing it?

RSXVRider Apprentice

RSXVRider

Posted
  • Author
Posted

1. Prepare. Bleed hose on nipple of the transfer case (just behind trans on drivers side). Open ATTESSA fluid bottle with funnel in.

2. Turn key to ACCESSORY on. Don't start car. 

3. Disconnect the pump wire 10cm up from the OBDII connector. Leave it disconnected. You will hear the pump 'cycle' ONCE.

4. Using 10mm open ring spanner, loosen bleed nipple. As the seal breaks open the pump will cycle in a 'rhythm'. as you undo the bleed screw more the 'rhythm' becomes a constant purge from the pump."

5. Go to the back of the car and as the funnel is already in your canister, simple pour more fluid in.

6. Over fill (past the line) in order to give you time to get back under the car and close the bleed valve.

7. Reconnect the single wire connector for the pump.

8. Turn key back to OFF.

9. Check fluid level.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • ARB26
      S1 Autech 260RS Wiring Diagrams

      By ARB26 · Posted

      Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • DanMac34
      R34 Speedo not working after manual swap

      By DanMac34 · Posted

      Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • funkymonkey
      Howdy Y'all

      By funkymonkey · Posted

      Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
×
×
  • Create New...