Jump to content
SAU Community

Recommended Posts

New guy with M35

Hey guys,

I've just bought my first stagea after wanting one for ages. M35 bone stock apart from a set of rims.

I love it. It needs a few things doing to it but that's half the fun.

It came with a full service history so I hope it's been looked after.

The one problem I do have and I have read EVERY post in here about it is my 4WD light is on.

what makes this so different? Well after reading a thread in here on how to clear codes (turn on, press acc pedal 5 times etc) my light goes off. I drive it and I have functioning 4WD (split torque gauge works).

BUT when I re start the car [normally] the light will be on so I'll turn car off, go through the code clearing actions and BooM, all good ????

My intention is to try the relay under the airbox , failing that I'll bleed the lines of any air.

Has anyone else had what I have described ?

Link to comment
https://www.sau.com.au/forums/topic/466787-new-guy-with-m35/
Share on other sites

Thanks Josh.

Thanks to all the information in this forum that was the first thing I checked. Currently my level is just above full.

Would that amount prevent the pump from pressurizing the system?

Also do you have any idea as to why I can clear the code and it works fine only for the code to return?

I'm reading all about how our cars are NOT OBDII so clearing them could be a hassle.

55 minutes ago, RSXVRider said:

Thanks Josh.

Thanks to all the information in this forum that was the first thing I checked. Currently my level is just above full.

Would that amount prevent the pump from pressurizing the system?

Also do you have any idea as to why I can clear the code and it works fine only for the code to return?

I'm reading all about how our cars are NOT OBDII so clearing them could be a hassle.

I don't have a stag yet but about to own one. Has done a bit of researching on this issue as well as the car i'm getting having the same problem.

By the sound of it, if any luck, a flush + new fluid my help you. There is also a big fuse (?) (20amp) somewhere that can be replace to fix the issue as well. If all of those mentioned still dont' fix it, better start sourcing a secondhand unit as the $2 pressure switch (built in) is known to fail and Nissan won't sell them separate.

1 hour ago, RSXVRider said:

Thanks west.

Well ive just found out that if i start the car with the synchro switched on i dont get the 4WD light on.
Fully functional 4WD.
Weird right.... lol.

Have heard of that as well but i'm afraid it's only a band-aid fix and not a long term solution, then again i could be wrong, only interpreting what i have read so far.

So i put my new relay in.
Statyed car. No 4ws light.
Small deive light stays off. Winning.
Turn car off.
Turn car on. Boom. 4wd light on again. Hmmmmmm.

Can anyone tell me what fuse is the 4wd? There are some big ones bwhind the battery but noting is labeled

It sounds like a pressure switch fault mate; very common. The best thing to do would be to get it on a scantool, and find out 100% what the fault is.

The fuse (it's more a fusible link) for the ATTESSA pump is in the block in front of the battery. 

It's labelled ETS from memory.

Thanks West. I hadn't seen that thread before.

I did try the disconnect single wire to the pump to bleed it but the pump wouldn't activate.

I'm going to give it another go on the weekend as i just read on another tread that you're supposed to bleed the gearbox nipple. I was attempting to bleed the ATTESSA pump nipple.

Plus one tread says to disconnect then bleed where as another one says to disconnect then re-connect straight away to bleed.

15 hours ago, RSXVRider said:

Thanks West. I hadn't seen that thread before.

I did try the disconnect single wire to the pump to bleed it but the pump wouldn't activate.

I'm going to give it another go on the weekend as i just read on another tread that you're supposed to bleed the gearbox nipple. I was attempting to bleed the ATTESSA pump nipple.

Plus one tread says to disconnect then bleed where as another one says to disconnect then re-connect straight away to bleed.

From this thread?

 

So after re reading all the threads I managed to work out the correct way to bleed the ATTESSA pump.

There was a ton of huge air bubbles in the line so I was quietly confident that was my problem.

I flushed the entire system with new fluid just to find my light is still on ..... Grrrrrrr

Well at least I know my pump actually works...

7 minutes ago, RSXVRider said:

So after re reading all the threads I managed to work out the correct way to bleed the ATTESSA pump.

There was a ton of huge air bubbles in the line so I was quietly confident that was my problem.

I flushed the entire system with new fluid just to find my light is still on ..... Grrrrrrr

Well at least I know my pump actually works...

So what's your method of doing it?

1. Prepare. Bleed hose on nipple of the transfer case (just behind trans on drivers side). Open ATTESSA fluid bottle with funnel in.

2. Turn key to ACCESSORY on. Don't start car. 

3. Disconnect the pump wire 10cm up from the OBDII connector. Leave it disconnected. You will hear the pump 'cycle' ONCE.

4. Using 10mm open ring spanner, loosen bleed nipple. As the seal breaks open the pump will cycle in a 'rhythm'. as you undo the bleed screw more the 'rhythm' becomes a constant purge from the pump."

5. Go to the back of the car and as the funnel is already in your canister, simple pour more fluid in.

6. Over fill (past the line) in order to give you time to get back under the car and close the bleed valve.

7. Reconnect the single wire connector for the pump.

8. Turn key back to OFF.

9. Check fluid level.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What an awesome idea to fit the facelift Lamborghini Diablo headlights. They are a perfect fit!
    • An update regarding the registration with the DVLA I sent off the paperwork the day after I collected the car from the port, two weeks later it was all returned with a letter explaining they have rejected the application. This was because the cheque was £20 short for the road tax (I used a price list I found online). Nevermind it is what it is, it was sent back to them the following day with a new cheque. Fast forward another 2 weeks or so, I called them for an update to be told it had been rejected. Yesterday (16th September) I received the documents back along with another letter, this time it was because I didn't put an X in one box on the V750 (personalised number plate certificate), which declared that I had the rights to the personalised number plate. Why this wasn't mentioned in the first rejection letter, I don't know, but it could have saved this headache. The documents were sent back today, so fingers crossed third times a charm and it'll FINALLY be registered on the road just in time for the bad weather (woohoo!) To cheer myself up I lowered the front 25mm, was sick of seeing it sit like a monster truck. No idea how much clearance I'll have getting on and off the driveway, I'll worry about that when I can actually drive it
    • You're going to miss not worrying about rust in the strut towers like the Skyline shitboxes out there
    • A few little updates that weren't filmed due to not taking long to do or not interesting enough for their own video. My new K&N Air Filter arrived, I went with an RU-4180 which matched the dimensions of the universal cone filter the car originally had.  The battery had gone flat, while that was charging I tidied up the spaghetti wiring at the bulk head and down the sides of the engine Next job was to swap the stereo The Kenwood harness had the female ISO plugs cut off and the male ISO plugs cut off the adaptor loom and joined with bullet connectors. I ordered in a repair loom through work and re-did it all. New Kenwood unit installed (Android Auto, DAB, Bluetooth, Reverse Camera) The bonnet/hood gas struts have been poor since collecting the car. I couldn't find any suitable replacements locally so took a chance on a pair from AliExpress.  The originals don't use a retaining clip to secure the cup onto the ball fixture, would explain why I struggled for 10-15mins trying to pry off the cups. The ball fixtures unscrew using a 12mm spanner, new ones are the same size. Sadly no photo of them fitted, you're not missing much lol The dished Momo steering wheel got replaced with my Momo Tuner, turns out I ordered counter sunk bolts for the horn trim ring (like they normally are for the steering wheel) instead of allen cap (flat seat)  A terrible photo of a Quaife style gear shift knob I've had stashed in my tool box for many years after purchasing the incorrect thread size (I can see a pattern emerging with ordering incorrect parts...) Also threw in a cup holder and a (empty) Boss Coffee can, because why not  
    • GT-R clearly the better choice! The 300 is certainly not insaly fast but has a decent amount of poke. Does a nice little drift around the corners with a decent amount of throttle. It's VERY predictable in a slide too.  Feels so progressive! People probably presume there's a 25 year old driving it based on my behaviour this week! 🤣
×
×
  • Create New...