Jump to content
SAU Community

Recommended Posts

Hey guys,

Heres a good place to vent, bitch and moan about the dramas we go through 2 get spare parts for our skylines.

Still trying to buy upper control arm inner suspension bushes. Whiteline dont seem 2 carry them, Nissan Australia dont have them ( but they will sell me a whole new control arm for $280 each).

If all spare parts are going to be this hard to track down, my car will be finished by the year 2013 :cry:

Do you have problems tracking down spare parts for your car?

Link to comment
https://www.sau.com.au/forums/topic/467-skylines-and-spare-parts-2002/
Share on other sites

I get all my spares from Jeep at Randwick. They can get anything from Nissan Jap within 2 weeks.

Call Tim on 96845777, they have the micro fish in english of the R32 R33 and R34, parts list.

Below are some of the tings I have got.

single DIM slot pocket $50

GTR factory cut keys $50

Interior dore clips $2.50

Rack and pinion rubber mounts $25

Stock GTR Vspec & N1 Shocks $400 a pair

  • 4 weeks later...
Originally posted by ONARUN

Hey akira. my right controll arm had to be imported from Jap. it took a while too :evil:

Tell me about it...im in the process of ordering controll arms, suspension arms....heaps of arms....from Japan after my little drifting incident that caused me to hit a gutter with my front wheel.:P:O :O

Hopefully should be all fixed ready to go next week....not sure what its going to cost though..i would imagine well over $1000. :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • HELP   Hey all, Is there an accelerator cable from another Nissan that can be used on the R33 GTST RB25DET with a Greddy forward facing plenum?  Thanks in advance  Rob 
    • Or do we think it was installed to give 1 bar of boost max, all day, everyday?
    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
×
×
  • Create New...