Jump to content
SAU Community

WANTED! DR30 LAMINATED WINDSCREEN

Conz

By Conz,
in Classic & Vintage (1950's-1980's)

 Share

Recommended Posts

Conz Newbie

Conz

Posted
Posted

WANTED! DR30 LAMINATED WINDSCREEN

Hey lads and ladies. 
Ripping my hair out trying to find a coupe front windscreen in aus that is laminated.. 
Any chance at all sedan screens fit?
Need this before the 8th of October.

My location is Toowoomba 4350. 
Nissan, Obrien ETC have part numbers that are different to the sedan screen that have been made obsolete.. 
Will take any condition at this stage as long as it's intact and I can get my compliance plate :):)

14195462_1433587603323969_3863590611633766201_o (1).jpg

13699554_10206851719758091_121912489_o.jpg

Link to comment
https://www.sau.com.au/forums/topic/467011-wanted-dr30-laminated-windscreen/
Share on other sites
Ghostrider Grand Master

Ghostrider

Posted
Posted

My parts book says #72712-27S00 for the hardtop Laminated Windscreen and it's still priced in Japan at about $600.00

I have asked Macarthur Nissan in Campbelltown to check if it is available and I will advise when I know more.

PM me with a contact number.

Cheers,

Dennis

  • Like 1
clubracer Community Regular

clubracer

Posted
Posted

I called Nissan too but to no avail. Called NZ and also Japan. If you get a different answer please let me know as I need one too and I was organising to have a batch made by a guy who does racing glass - for anyone else that wants one please let me know. I can also have them done with a heated element.

  • Like 1
  • 1 month later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      NC MX5

      By MBS206 · Posted

      This sounds like someone who would have owned an R33 in their past... It's okay, I'm 100% picking up what you're putting down Mark.
    • MBS206
      Jacks that fit under GTR lips that can reach the subframe?

      By MBS206 · Posted

      Just back on what was raised about jacking off the the tow/tie down point on the front of cars. I've used it plenty. I've also watched it on a car where you could see it move the front end of the car. It was like the front end/whole car being tweaked and twisted a bit. I will say, I struggle to find good jacking points on MOST cars. The ones that have good points, I then normally struggle to find a jack tall enough to make the car change height!   One of my go to points for either the jack, or the axel stands though, is either a suspension pickup point, OR a subframe to chassis major bolting point. I actually think its the subframe on my R33 that has a bit of a bend in it, from being jacked in the middle too. However, it could have been one of my many other cars I've had over the years! Or it could also be the from me jacking it up, and the fact the top of the front radiator support isn't there, so it can allow the front of the car to move and bend etc.
    • GTSBoy
      M35 Aftermarket Fuel Pump

      By GTSBoy · Posted

      My apologies. I forgot we were talking about weird beard M series stuff. Had been talking elsewhere with someone about an R33 with similar subject and got confused.
    • The Bogan
      NC MX5

      By The Bogan · Posted

      Nope, I don't like the look of ND RF, or any ND really, I don't like their faces or arses, why, because of their "modern" lines, the NC, whilst "modernish" has a more rounded shape that I like Well, that's how my overly judgemental eyes see it anyway  
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Should be more than fine, especially the overall fuel pressure would never exceed 3.5bar (assuming that thing never gets more than 0.5bar of boost in stock form). According to the chart, it's 11amps.
×
×
  • Create New...